User manual HOTPOINT NMTP 1918 FW

[. . . ] Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. This equipment should be installed and operated with at least 20cm and more between the radiator and person's body (excluding extremities: hands, wrists, feet and ankles). For customers who use this product in the following countries: Norway: Use of this radio equipment is not allowed in the geographical area within a radius of 20 km from the centre of Ny-Alesund, Svalbard in Norway. For customers in Europe Properly shielded and grounded cables and connectors must be used for connection to host computers and/or peripherals. [. . . ] You can enjoy the PARTY STREAMING function with other devices* that have this PARTY STREAMING logo shown below. * Available PARTY STREAMING-compliant devices may differ depending on the countries or regions. For details on available devices, contact your nearest Sony dealers. 44GB Joining a PARTY The system can join a PARTY that has been started by another device so that you can enjoy the same audio content being played in a different room. PARTY STREAMING in a wireless LAN environment With some IEEE802. 11n-compatible wireless LAN routers/access points, the wireless LAN transfer speed may slow down when "WEP" or "WPA/WPA2-PSK (TKIP)" is selected for the encryption method. If the sound skips during streaming playback using the PARTY STREAMING function, try changing the encryption method to "WPA/ WPA2-PSK (AES). " This may improve the transfer speed and the streaming playback. Configurations of encryption vary depending on the model; please refer to the operating instructions supplied with your router/access point. You can also obtain support information about wireless LAN settings on the following websites. For customers in Europe: http://www. sony. net/audio/netsettings For customers in Oceania: http://www. sony-asia. com/support While the PARTY host device is having a PARTY, press PARTY. "JOIN PARTY" appears, and the system joins the PARTY as a PARTY guest. To leave a PARTY Press PARTY. "LEAVE PARTY" appears, and the system leaves a PARTY. Tip If "Network Standby" is set to "On, " the system turns on and joins the PARTY automatically when the PARTY host device starts the PARTY. Operations Notes · You cannot join a PARTY in the following cases: ­ you have a PARTY on this system. ­ you have already joined another PARTY. · If you press PARTY when no PARTY is started, but a device complying with PARTY STREAMING function is playing, the device will be the PARTY host, and the system will join the PARTY as a PARTY guest. The PARTY guest device function automatically switches to HOME NETWORK when the device joins a PARTY. Confirm the message and also read the "END-USER LICENSE AGREEMENT FOR HOTPOINT SOFTWARE" (page 80), then press ENTER. · Make sure not to turn off the system, disconnect the · network cable or perform any operation on the system while the updating operation is in progress. If you try to update the software when the Sleep Timer is on, the Sleep Timer will turn off automatically. 1 2 3 4 5 Select HOME NETWORK, MUSIC SERVICES or AirPlay as the function. 8 Press M/m to select "Agree, " then press ENTER. The system starts to update the software. It may take a while (about 20 minutes at the longest) for the system to finish the update. The required time will depend on the amount of data in the updates, the line type of the network, the network communication environment, etc. Push power on the unit. " appears after the software update is finished. Press ?/1 on the unit to turn off the system, and the system is updated to the new version. Press OPTIONS. Press M/m to select "Network, " then press ENTER. Press M/m to select "Software To cancel the procedure Select "Cancel" in step 7. Update, " then press ENTER. To go back to the previous screen Press M/m to select "Update, " then press ENTER. The system starts checking the available software update. Press BACK before the receiver starts the software update. You cannot go back to the previous screen when the update starts. 48GB Listening to audio material from an external component You can listen to the playback audio from an external component (such as a portable music player, etc. ) connected to the AUDIO IN 1 or AUDIO IN 2 jack on the unit. Use an audio connecting cable (not supplied) to connect the AUDIO IN 1 or AUDIO IN 2 jack on the unit and the audio output jack on the external component. Make sure the audio connecting cable (not supplied) is firmly inserted into both jacks. If not, noise may be generated in the audio output. the connected component, refer to the operating manual supplied with the connected component. Notes · Lower the volume on this system using VOLUME ­ before disconnecting the external component. · The system may enter standby mode automatically if the volume level of the connected component is too low. [. . . ] By using the HOTPOINT SOFTWARE, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this EULA, HOTPOINT is unwilling to license the HOTPOINT SOFTWARE to you. In such event, you should not use the HOTPOINT SOFTWARE. HOTPOINT SOFTWARE LICENSE The HOTPOINT SOFTWARE is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The HOTPOINT SOFTWARE is licensed, not sold. GRANT OF LICENSE All title, copyright and other rights in and to the HOTPOINT SOFTWARE are owned by HOTPOINT or its licensors. [. . . ]