User manual HOTPOINT PC 750 T

[. . . ] 13 Operating Instructions HOB Contents IT Italiano, 1 GB GB English, 14 FR Français, 27 Installation, 15-19 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications ES Español, 41 Description of the appliance, 20 Overall view Start-up and use, 21-23 Practical advice on using the burners Practical advice on using the electric hotplate Precautions and tips, 24 PC 750 T X /HA PC 750 T AX /HA PC 750 T GH /HA PC 750 T XX /HA PC 750 T R /HA PC 750 T /HA PC 760 F X /HA PC 760 F R /HA PC 750 X /HA PC 750 AX /HA PC 730 RT GH /HA PC 730 RT X /HA PC 640 T X/HA PC 640 T GH/HA PC 640 T AX/HA PC 640 T R/HA PC 640 X/HA PC 640 /HA PC 631 X/HA PC 631 /HA General safety Disposal Maintenance and care, 25 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 26 14 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] The two nozzles have the same hole diameter. Replace all the components by completing the above operations in reverse order. GB • Adjusting the burners’ primary air : Does not require adjusting. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). 78 MJ/m³ 18 A R S Ø145 R A S S RR A TC S GB PC 631 X/HA PC 631 /HA PC 640 X/HA PC 640 R/HA PC 640 /HA PC 640 T X/HA PC 640 T GH/HA PC 640 T AX/HA PC 640 T R/HA S DC TC RR UR A S S RR TC A S S RR A S A SP SP PC 730 RT GH /HA PC 730 RT X /HA PC 750 X /HA PC 750 AX /HA PC 750 T X /HA PC 750 T AX /HA PC 750 T GH /HA PC 750 T XX /HA PC 750 T R /HA PC 750 T /HA PC 760 F X /HA PC 760 F R /HA DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 19 Description of the appliance GB Overall view GAS BURNERS ELECTRIC HOTPLATE* Support Grid for COOKWARE Control Knobs for GAS BURNERS and ELECTRIC HOTPLATE* Indicator Light for ELECTRIC HOTPLATE* Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • The INDICATOR LIGHT FOR ELECTRIC HOTPLATES* switches on whenever the selector knob is moved from the ‘off’ position. • GAS BURNERS differ in size and power. The knob marked by the symbol external burner; The knob marked by the symbol internal burner. Operates the operates the To turn on one of the rings, press the relative knob in all the way and turn it anti-clockwise to the high . The burner is fitted with an electronic setting igniter that automatically starts when the knob is pressed in. Since the burner is equipped with a safety device, after lighting the burner keep the knob pressed in for about 2-3 seconds to allow the device which keeps the flame lit automatically to heat up. The selected burner can be regulated using the corresponding knob, as follows: • Off Maximum Minimum To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). Electric hotplates* The corresponding knob may be turned clockwise or anti-clockwise and set to six different positions: Setting Normal or Fast Plate 0 1 2-5 6 Off Low Medium High GB When the selector knob is in any position other than the off position, the ‘on’ light comes on. [. . . ] € For hobs which ligth automatically, the terminal part of the electronic instant lighting devices should be cleaned frequently and the gas outlet holes should be checked for blockages. € The electric hotplates should be cleaned with a damp cloth and lubricated with a little oil while still warm. € Stainless steel can be marked by hard water that has been left on the surface for a long time, or by aggressive detergents containing phosphorus. After cleaning, rinse and dry any remaining drops of water. [. . . ]