User manual HOTPOINT PH 960 T GH AUS.1

[. . . ] PH 960 T GH AUS. 1 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 3 Description of the appliance, 4 Installation, 5 Start-up and use, 9 Precautions and tips, 9 Maintenance and care, 10 Troubleshooting, 10 Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] Connection with a rigid pipe (copper or steel) !Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment. Flexible hose assembly (if used) must comply with AS/NZS 1869 Class B or D, be of appropriate internal diameter, be kept as short as possible (not to exceed 1. 2 metres), must not be kinked or in contact with any hot surface. The supply connection point shall be accessible with the appliance installed. Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Never use a flame. ELECTRONIC IGNITION L N PA1 . . . . . . . PAn IGNITION SWITCH WIRING DIAGRAM Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical see data plate connections ECODESIGN This appliance conforms to the EU Regulation no. 66/2014 implementing Directive 2009/125/EC. standard EN 30-2-1 7 GB Burner and nozzle specifications Natural gas (1. 0 kPa) Burner Rapid (R) Semi Rapid (S) Auxiliary (A) Triple Crown (TC) Fish Burner (FB) Total Ø Injector (mm) 1. 29 1. 10 0. 80 1. 75 1. 01 ULPG (2. 75 kPa) GC (MJ/hr) Ø Injector GC (MJ/hr) (mm) 8. 3 6. 0 3. 3 14. 50 4. 5 41. 1 0. 80 0. 64 0. 50 1. 05 0. 64 8. 5 5. 0 3. 0 13. 7 5. 2 40. 6 S TC FB A R PH 960 T GH AUS. 1 8 Start-up and use !The position of the corresponding gas burner is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: ● Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “●” position). Practical Advice on Using the Half Fish-Kettle Burner The two “Half Fish-Kettle” burners, are eliptic in form and can be turned up to 90°. This makes the cooktop more flexible in terms of how it can be used. GB To turn the two burners 90°, proceed as follows: • Make sure that the burners are cool; • Lift the burner completely out of its housing; • Replace it in its housing in the position desired; • Make sure that the burners are positioned correctly before use. [. . . ] This procedure must be performed by a qualified technician authorised by the manufacturer. Service Annual servicing by an authorised person is recommended. If the appliance produces unusual odour, yellow tipping flame, flame lifting off the burner or is not perfroming as per theoriginal installation, or for service please contact: Arisit Pty Ltd 1300 762 219. 0 Respecting and conserving the environment • Cook your food in closed pots or pans with well-fitting lids and use as little water as possible. Cooking with the lid off will greatly increase energy consumption. [. . . ]