User manual HOTPOINT PO 740 ES

[. . . ] Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. [. . . ]  check that the supply pressure complies with the values indicated in table 1 “Characteristics of the burners and nozzles” since this will ensure safe operation, correct consumption and ensure a longer life to your appliance. Connection with hose Make the connection using a gas hose complying with the the characteristics provided in current directive. The internal diameter of the pipe used is as follows: - 8mm for liquid gas; When installing the hose, remember to take the following precautions: Check that the hose fits firmly into place at the two ends and fix it with clamps complying to current directive. If any of the above recommendations can not be adopted, flexible metal pipes should be used. Tight control  When installation has been completed, check the pipe fitting for leaks with a soapy solution. Once the connection has been made, ensure that the flexible metal tube does not touch any moving parts and is not crushed. Regulation of Air Supply to the Burner The burners do not need a primary air regulator. - 2002/96/EC 24 Burner and nozzle specifications Table 1 Burner Diameter (mm) By-Pass 1/100 (mm) Fast (R) Semi Fast (S) Auxiliary (A) Supply Pressures 90x90 65x65 45x45 39 28 28 Nominal (kPa) Minimum (kPa) Maximum (kPa) Liquid Gas Nozzle 1/100 (mm) 86 70 50 nominal 220 140 65 30 25 35 Flow g/h minim 50 25 25 GB A R S S PO 740 ES/HA 25 Description of the appliance GB Overall view GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. • Control Knobs for GAS BURNERS adjust the power or the size of the flame. GAS BURNER ignition* enables a specific burner to be lit automatically. • SAFETY DEVICE* stops the gas flow if the flame is accidentally extinguished. 26 Start-up and use The position of the corresponding gas burner is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: • Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. To light a burner, simply press the corresponding knob all the way in and then turn it in the counterclockwise direction to the "High" setting, keeping it pressed in until the burner lights.  If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “•” position). Practical advice on using the burners To ensure the burners operate efficiently: • Use appropriate cookware for each burner (see table) so that the flames do not extend beyond the bottom of the cookware. • Always use cookware with a flat base and a cover. [. . . ] All major household appliance manufacturers are active in the creation of systems to manage the collection and disposal of old appliances. 28 Maintenance and care Switching the appliance off Disconnect your appliance from the electricity supply before carrying out any work on it. Gas tap maintenance Over time, the taps may become jammed or difficult to turn. If this happens, the tap must be replaced. [. . . ]