User manual HOTPOINT PZF 950 T GH N /HA

[. . . ] Com 13 Operating Instructions HOB Contents IT Italiano, 1 GB GB English, 14 FR Français, 26 Installation, 15-20 NL Nederlands, 38 ES Espanol, 50 Positioning Gas connection Electrical connection Data plate Burner and nozzle specifications Description of the appliance, 21 Overall view Start-up and use, 22 Advice when using burners Precautions and tips, 23 General safety Disposal PZF 950 T GH N/HA Care and maintenance, 24 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 25 Installation  Please keep this instruction booklet in a safe place for future reference. If the appliance is sold, given away or moved, please make sure the booklet is also passed on to the new owners so that they may benefit from the advice contained within it. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas which are below ground level (cellars, etc. Only the cylinder currently being used should be kept in the room. [. . . ] electrical connection THE EQUIPMENT MUST BE EARTHED CORRECTLY. The hobs are designed for operation with an alternating current at the power supply voltage and frequency indicated on the data plate (this is located underneath the hob; alternatively the information may be found at the end of the instruction manual). Make sure that the local power supply voltage value is the same as the value indicated on the data plate. 6 18 Connecting the power supply cable to the mains Models which do not already have a plug should be fitted with a plug which has been standardised for the charge indicated on the data plate and then connected to a suitable electrical socket. If direct connection to the electricity mains supply is required, an omnipolar switch with a minimum contact opening of 3 mm must be installed between the appliance and the mains. The switch must be suitable for the charge indicated and must comply with current electrical regulations. The yellowgreen wire must not be interrupted by the switch. The supply cable must not be placed in areas where it could reach temperatures higher than 50 ?If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be performed separately, both for electrical safety purposes and to make extracting the oven easier. Do not use reduction devices, adaptors or shunt devices, as these may cause overheating or burning. Before connecting the appliance to the power supply, make sure that: • the modulating valve and the electricity supply can withstand the maximum power of the appliance (see the data plate for details); • the supply system is earthed correctly, in compliance with current laws and regulations; • the power socket or omnipolar switch may be reached easily once the hob has been installed. wE HEREBY DECLINE ALL LIABILITY WHEREVER ACCIDENT PREVENTION LEGISLATION HAS NOT BEEN OBSERVED. Replacing the cable Use a H05RR-F rubber cable with a cross-section of 3 x 0. The yellow-green wire should be 2 or 3 cm longer than the other wires. 78 MJ/m3 B D C B A PZF 950 T GH N/HA 20 Description of the appliance Overall view GAS BURNERS Support grid for COOKWARE GB Control knobs for the GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS vary in size and power. Select the most suitable burner in accordance with the diameter of the cookware you wish to use. • Control knobs for the GAS BURNERS adjust the flame or power setting. GAS BURNER ignition* enables a specific burner to be lit automatically. • SAFETY DEVICE* stops the gas flow if the flame is extinguished accidentally. IT Start-up and use GB  The position of the corresponding gas burner is shown on every knob. Repairs carried out by inexperienced individuals may cause injury or further malfunctioning of the appliance. contact a Service Centre (see Assistance). [. . . ] After cleaning, rinse well and dry thoroughly. Any remaining drops of water should also be dried. 24 Troubleshooting On rare occasions, the appliance may fail to work. Before contacting the Service Centre, check whether you can resolve the problem easily yourself, using the list below. [. . . ]