User manual HOTPOINT SBD 2022 Z/HA

[. . . ] 12 Operating Instructions REFRIGERATOR/FREEZER COMBINATION Contents I Italiano, 1 GB English, 13 F Français, 25 Installation, 14 GB Positioning and connection Reversible doors Description of the appliance, 15-16 Control panel Overall view E Espanol, 37 PT Portuges, 49 PL Polski, 61 Start-up and use, 17-18-19 Starting the appliance Navigating the display Pure Wind Using the refrigerator to its full potential Using the freezer to its full potential Maintenance and care, 20-21 SBD 2022 Z/HA Switching the appliance off Cleaning the appliance Avoiding mould and unpleasant odours Defrosting the appliance Replacing the light bulb Precautions and tips, 22 General safety Disposal Respecting and conserving the environment Troubleshooting, 23 Assistance, 24 Installation GB !Before placing your new appliance into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance. Please keep these operating instructions for future reference. [. . . ] Once this time has elapsed the LED remains lit constantly: place the food inside the freezer and close the door. After 24 hours the food will have been frozen properly and the function will be deactivated automatically (the LED switches off); the food may now be moved into the two lower compartments (so that the Cool Care Zone can be used if necessary) or even left in the Cool Care Zone compartment, which operates as a normal storage compartment when the function has not been activated. B A B A B Pure Wind maximises air circulation, improving the efficiency of the evaporator and helping to achieve the optimal temperature inside the refrigerator as quickly as possible each time it has been opened. The blown air (A) is cooled when it comes into contact with the cold wall, whereas the hotter air (B) is sucked up (see diagram). GB 19 Maintenance and care Assistance GB Switching the appliance off During cleaning and maintenance it is necessary to disconnect the appliance from the electricity supply: 1. Press and hold the ON/OFF button for approximately two seconds, until everything on the display switches off apart from the red LED corresponding to the ON/ OFF button. If this procedure is not followed, the alarm may sound. This alarm does not indicate a malfunction. To restore normal operation, it is sufficient to hold the ON/OFF button down for more than two seconds. To disconnect the appliance, follow points 1 and 2. Defrosting the refrigerator compartment The refrigerator has an automatic defrosting function: water is ducted to the back of the appliance by a special discharge outlet (see diagram) where the heat produced by the compressor causes it to evaporate. It is necessary to clean the discharge hole regularly so that the water can flow out easily. Defrosting the freezer compartment If the frost layer is greater than 5 mm, it is necessary to defrost manually: 1. The day before defrosting, press the SUPER FREEZE button (the yellow SUPER FREEZE indicator light illuminates) to further cool the food. The function is automatically disabled after 24 hours, or it may be disabled at any moment by pressing the SUPER FREEZE button again. Press and hold the ON/ OFF button for approximately two seconds, until everything on the display switches off apart from the red LED corresponding to the ON/OFF button. Wrap frozen foods in newspaper and place them in another freezer or in a cool place. Leave the door open until the frost has melted completely. This can be made easier by placing containers with lukewarm water in the freezer compartment. Certain appliances are fitted with the DRAIN SYSTEM to lead the water outside (see diagram). Cleaning the appliance • The external and internal parts, as well as the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and bicarbonate of soda or neutral soap. • The back of the appliance may collect dust which can be removed by delicately using the hose of a vacuum cleaner set on medium power. [. . . ] To remove the “A2” message from the display and restore normal freezer operation, press one of the freezer temperature adjustment buttons twice or switch the product off and on again. The alarm sounds, the ALARM icon flashes on the display and “A2” appears on the freezer display. The refrigerator and the freezer do not • The doors do not close properly or the seals are damaged. • The temperature that has been set is too high (see Start-up and use). [. . . ]