User manual HOTPOINT TCD 83B 6K/Z

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HOTPOINT TCD 83B 6K/Z. We hope that this HOTPOINT TCD 83B 6K/Z user guide will be useful to you.

Lastmanuals help download the user guide HOTPOINT TCD 83B 6K/Z.


Mode d'emploi HOTPOINT TCD 83B 6K/Z
Download
Manual abstract: user guide HOTPOINT TCD 83B 6K/Z

Detailed instructions for use are in the User's Guide.

[. . . ] Instruction booklet TUMBLE DRYER GB English, 1 F Français, 18 E Español, 35 Contents Important information, 2-3 Installation, 4 Where to put your dryer Ventilation Water drain Electrical connection Before you start using your dryer GB P NL Português, 52 Nederlands, 69 Dryer description, 5 The features Control panel The Display, 6-8 Start and programmes, 8-11 Choosing a programme Special programmes Programme option modifiers Table of programmes The controls TCD 83B First time you turn on your dryer you must select your preferred language see page 6 Laundry, 12-13 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 14 General safety Saving energy and respecting the environment Maintenance and Care, 15 Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Empty the water container after each cycle Cleaning the condenser unit Cleaning the dryer Troubleshooting, 16 Service, 17 Disposal !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. [. . . ] After re-starting the dryer the message will take a few seconds to go out. To avoid this always empty the water container each time you use the dryer (see Maintenance). — During a delay phase the delay will continue to count down. The Start/Pause button must be pressed to resume the delay programme. the display will change to show current status. — During the drying part of the programme, the colons on the display stop flashing to show that the time has stopped counting down. The Start/Pause button must be pressed to resume the programme. The display will change to show the current status, the colons flash and count down continues. — During the Post Care phase, the programme ends. Pressing the Start/Pause button will restart a new programme from the beginning. — Note If you have a power cut, switch off the power or remove the plug. When power is restored, press the Start/Pause button and the programme will resume. Warning, after pressing the Start/Pause button , the programme cannot be changed. Select the new programme and any options required, the light will then flash green. Press the Start/Pause button again and the new programme will start. — Option buttons These buttons are used to customise the selected programme to your requirements. Not all options are available for all programmes (see Programmes Table). If an option is not available and you press the button, the buzzer will beep 3 times. If the option is available the indicator, on the display unit above the bottom buttons, lights to show that the option has been selected. Time Delay (Delay Timer) The start of some programmes (see The Display and Programmes tables) can be delayed for up to 24 hours. Ensure the water container is emptied before setting a delayed start. crease Care The pre-care option is only available if a delayed start has been selected. [. . . ] Clean the filter and the condenser (see Maintenance). Then replace the plug, turn on and start another programme. if F10 or F15 is still displayed contact the Service Centre (see Service). If any other number is shown: Note down the code and contact the Service Centre (see Service). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HOTPOINT TCD 83B 6K/Z

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HOTPOINT TCD 83B 6K/Z will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag