User manual HOTPOINT WMG 10437SX EX.60HZ

[. . . ] Instructions for use WASHING MACHINE Contents GB English, 1 GB ES Español, 15 PT Português, 29 Installation, 2-3-4-5 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data AR ،‫34, عربي‬ Care and maintenance, 6 Cutting off the water and electricity supplies Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and advice, 7 General safety Disposal Opening the porthole door manually Description of the washing machine, 8-9 WMG 10437 Control panel Display Running a wash cycle, 10 Wash cycles and options, 11 Table of programmes and wash cycles Wash options Detergents and laundry, 12 Detergent dispenser drawer Preparing the laundry Special wash cycles Troubleshooting, 13 Service, 14 1 Installation GB !This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/ herself with its operation and features. Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance. [. . . ] To deactivate the control panel lock, press and hold the button for approximately 2 seconds. Standby mode This washing machine, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again. TEMPERATURE button: press to reduce or completely exclude the temperature; the value appears on the display. SPIN button: press to reduce or completely exclude the spin cycle; the value appears on the display. 8 Display B GB A C The display is useful when programming the machine and provides a great deal of information. The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED START option has been set, the countdown to the start of the selected wash cycle will appear. Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle. The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle appear in section B: Main wash Steam Refresh Rinse Spin and Pump out The icons corresponding to “temperature”, “spin” and “delayed start” (working from the left) are displayed in section C. The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle. The “spin” bars indicate the maximum spin level which may be selected for the set cycle. The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display. dOOR LOCKED indicator light: The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door. To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched off the door may be opened. Press the button; the START/PAUSE indicator light will flash slowly in a green colour. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes and wash cycles on the following page. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Detergents and laundry”. Use the WASH CYCLE SELECTOR knob to select the desired wash cycle. A temperature and spin speed is set for each wash cycle; these values may be adjusted. The duration of the cycle will appear on the display. Use the relevant buttons: Modify the temperature and/or spin speed. [. . . ] When running the programme, do not mix garments of 12 Troubleshooting Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list. gB Problem: The washing machine does not switch on. Possible causes / Solutions: • The appliance is not plugged into the socket fully, or not enough to make contact. [. . . ]