User manual HP COLOR LASERJET CM1015/CM1017 MFP

[. . . ] HP Color LaserJet CM1015/CM1017 MFP User Guide HP Color LaserJet CM1015/CM1017 MFP User Guide Copyright and License © 2006 Copyright Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. [. . . ] Duplicate IP address detected: Another networked device has the same IP address assigned. Contact the network administrator to resolve this issue. Review under the TCP/IP section of the Network Hardware Configuration page the IP configured by method: 3. Verify the TCP/IP address, subnet mask, and default gateway are correct. DHCP: Automatically assigned TCP/IP address by the dynamic host controller protocol (DHCP) server. BOOTP: Manually assigned TCP/IP address by the BOOTP server. AUTOIP: Default address assigned for Link Local connection (no DHCP or BOOTP server available). Can you "ping" the MFP?Use the command prompt to ping the MFP from the computer. For example: ping 192. 168. 0. 10 Ensure that the ping displays round-trip times. If you can ping the MFP, verify that the IP address configuration for the MFP is correct on the workstation. If it is correct, uninstall and re-install the MFP software. If the ping command failed, verify that the network hubs are on, then verify that the network settings, the MFP, and the computer are all configured for the same network. 4. Are other MFPs able to print? 108 Chapter 11 Network Setup and Administration (HP Color LaserJet CM1017 MFP) ENWW If yes, the problem is workstation-specific. Verify that both workstations are using the same network settings. Do not assign identical TCP/IP addresses to two network devices on the same If network communication is not resolved by using steps 1 through 3, or if other users can not print, reset all network configuration settings to factory-defaults by selecting Restore defaults from the control panel. After the MFP automatically power cycles, wait four to six minutes and verify that the network functionality is working properly. Contact the network administrator for more information. ENWW Set up the MFP and use it on the network 109 110 Chapter 11 Network Setup and Administration (HP Color LaserJet CM1017 MFP) ENWW 12 How do I? Use this section to perform basic tasks with the HP Color LaserJet CM1015/CM1017 MFP Series. Control panel and other settings: How do I?(HP Color LaserJet CM1017 MFP only) Network: How do I?(HP Color LaserJet CM1017 MFP only) Maintenance: How do I? ENWW 111 Control panel and other settings: How do I? This section discusses control-panel settings. HP Color LaserJet CM1017 MFP control panel features The HP Color LaserJet CM1017 MFP contains the following lights and buttons on the control panel: NOTE Print a demo page by pressing the Scan To and Start Scan buttons simultaneously. 1 Graphical display. Supplies gauges: Displays consumption levels of print cartridges. Appears when the MFP shows the Ready state with no warnings, or when the MFP shows a warning or error message pertaining to a print cartridge or multiple supplies. When the supply is empty the gauge displays as empty. Flashing indicates a single supply is empty. [. . . ] 3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name or the product number(s). Boise, Idaho 83714-1021, USA January 4, 2006 For regulatory topics only: Australia Contact: Product Regulations Manager, Hewlett-Packard Australia Ltd. , 31-41 Joseph Street, Blackburn, Victoria 3130, Australia. European Contact: Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard Gmbh, Department HQ-TRE / Standards Europe, Herrenberger Strasse 140, D-71034 Böblingen, Germany, (FAX: +49-7031-14-3143) USA Contact: Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160, Boise, Idaho 83707-0015, USA, (Phone: 208-396-6000) ENWW Declaration of conformity 237 Country/region-specific safety statements Laser safety statement The Center for Devices and Radiological Health (CDRH) of the U. S. [. . . ]