User manual HP COMPAQ USB 3-BUTTON OPTICAL MOBILE MOUSE QUICK START GUIDE

[. . . ] The information in this document is subject to change without notice. The information in this publication is subject to change without notice and is provided "AS IS" WITHOUT WARRANTY OF ANY KIND. THE ENTIRE RISK ARISING OUT OF THE USE OF THIS INFORMATION REMAINS WITH RECIPIENT. IN NO EVENT SHALL COMPAQ BE LIABLE FOR ANY DIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE OR OTHER DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION), EVEN IF COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. [. . . ] Use when the originals are black text or line art. This mode provides the fastest fax speed, but resolution is 203 x 98 dpi. (Standard is only available for the Black Fax Type) Use when the originals are black text or line art. Slower than Standard, but resolution is 203 x 196 dpi. Use when the originals are small black text or line art. Slower than Fine, but resolution is 300 x 300 dpi. (Super Fine will not scan to memory due to large memory requirements) Adjust this when your originals are too light or too dark. When on, all faxes will be scanned into memory and then faxed. When off, all faxes will be scanned and faxed at the same time. Fax Resolution · · · Standard Fine Super Fine Dark to Light On Off Fax Contrast Fax Memory Xmit · · · 38 Speed Sending Up to 70 Speed Send numbers are set up on the host computer using the Compaq A1500 Settings Utility as described in the "Speed Send Settings" section of the Using the A1500 Settings Utility chapter. Once the Speed Send numbers are set up, you are ready to begin faxing with Speed Send. Load the documents printed side facing down in the document input tray. Use the Compaq A1500 Settings Utility to print a confirmation report each time faxing is complete or when there is an error. See the "Compaq A1500 Settings Utility" section on Fax settings. You can change the Fax Receive Mode either on the computer using the A1500 Settings Utility or by pressing the Setup button on the front control panel. While you are printing from the computer to the All-In-One, an incoming fax will be received into memory. However, other tasks such as copying or sending a fax may temporarily reduce the amount of memory available. Receiving Automatically in FAX Mode In FAX mode, the A1500 answers an incoming call on the second ring and receives the fax automatically. Use the Settings Utility to change the number of rings the A1500 will wait before answering the call. The fax mode is recommended when you have a dedicated telephone line for your Compaq A1500. Redial Pressing the Redial button dials the number that was last entered. You can also modify the number using the Clear button and the numeric keypad. Automatic Redial When you send a fax, if the number you have dialed is busy or there is no answer, the A1500 hangs up, waits for a specified interval, and redials the number. When this occurs, the LCD panel shows the retry count and the number of minutes left before the next retry. If after a specified number of retry attempts (retry count) the All-In-One fails to connect, the machine returns to the Ready state. Set the retry interval and count using the Compaq A1500 Settings Utility. Receiving Automatically in ANS/FAX Mode To use this mode, you must attach an answering machine to the EXT socket on the All-In-One. In ANS/FAX mode, your answering machine answers the incoming call and the caller can leave a message on the answering machine. If a fax tone is on the line, the call automatically switches from the answering machine to the A1500. If your answering machine has a user-selectable ring counter, set it to answer calls within the fewest possible rings. If your answering machine is turned off, or no answering machine is connected to the A1500, the A1500 will automatically attempt to receive a fax after 6 rings. Press the Stop button to stop sending a fax that is trying to transmit. Pressing the Stop button during the retry period will bring up the following message: Receiving Manually in TEL Mode If more than one job is trying to transmit, use the Options button to select the job you want to stop then press the Stop button to stop your selection. [. . . ] The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 0. 75 mm2 / 18AWG and the cord should be between 5 and 6. 5 feet (1. 5 and 2 meters) long. If you have questions about the type of power cord to use, contact your Compaq authorized service provider. Route the power cord so that it will not be walked on, tripped over, or pinched by items placed upon or against it. [. . . ]