User manual HP DESIGNJET 430 PRINTER

[. . . ] R HP DesignJet 430 Printer HP DesignJet 450C Printer HP DesignJet 455CA Printer User's Guide Setup instructions - see chapter 1 Upgrade instructions - see chapter 6 E Copyright Hewlett-Packard Company 1997 Manual part number C4713-90021 First edition, July 1997 Second edition, October 1997 Printed in Europe. Customer re-order number C4713-60041 All rights are reserved. No part of the document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. AutoCADTM is a trademark of Autodesk Inc. [. . . ] 2 If the problem continues perform the Accuracy Calibration (see page 6­11) and print the Print Quality Test Print again to see if there has been any improvement. 5­16 Special internal prints Using the Print Quality Test Print Test 5 (Color Variation) This test produces four boxes in yellow, black, cyan and magenta. In each box there are two horizontal bands; the lower band is a 100% shade, the upper band is shaded from 100% scaling to 60%. The purpose of this test is to determine at what percentage the upper shading becomes visible from the lower band. The best way to do this is to cover the box with a piece of paper and slide the paper horizontally across the box. Stop as soon as you see a different shade in the upper box. You can then determine the percentage scaling from the figure at the top or bottom of the box. Correct Incorrect If the upper box shading is never visible or is visible only at a very low percentage, it is an indication that the cartridge is producing incorrect size ink drops. Try the following: 1 Replace the failing cartridge and print the Print Quality Test Print again. Test 6 (Banding Test) This test pattern is a long dark stripe and is not numbered on the Print Quality Test Print. It can be found on the left-hand side of the other test patterns. Banding consists of random dark or light bands in area fills. There are two types of banding: Negative banding: This means that consecutive swaths overlap each other, creating dark bands. Positive banding: This means that consecutive swaths do not touch, thus leaving a small gap between each other. This then causes white (or lighter colored) bands. 5­17 5 INTERNAL PRINTS Special internal prints Using the Print Quality Test Print Correct Incorrect If there is negative or positive banding in the test image, try the following: 1 Perform the Accuracy Calibration (see page 6­11) and print the Print Quality Test Print again to see if there has been any improvement. 2 Remove the all cartridges and clean the flex contacts on the carriage and the cartridges. Reseat the cartridges and try the test again. 3 If the error is still present, replace the cartridges and print the Print Quality Test Print again. 5­18 6 Reconfiguring your printer 6­1 6 RECONFIG­ URATION To see the current configuration of the printer 6­2 To change the serial interface settings 6­3 To change the graphics language setting for less common applications 6­3 To change the I/O timeout setting 6­4 To upgrade your printer with more memory 6­4 To upgrade your printer with a network interface 6­4 To upgrade the HP DesignJet 430 printer with color 6­5 Recalibrating the printer for accuracy 6­11 Reconfiguring the printer To see the current configuration of the printer To see the current configuration of the printer To see the current configuration of your printer, print the Setup Sheet, as explained on page 1­19. Those items on the Setup Sheet which you may change are listed on page 1­22, together with their defaults. They are explained in the relevant chapters of this manual, for example Page Size in chapter 3 and Graphics Language in this chapter. The following three items, which appear near the top right-hand corner of the Setup Sheet, tell you the overall configuration of the printer. Item RAM Comments This is the size, in megabytes, of the printer's main standard memory, plus the amount of memory reserved for printing. D This does not correspond directly to the size of your files on the computer, as explained on page 6­4. [. . . ] For details, see under "Ordering accessories" in chapter 10. DOC MAP These documents are supplied with this printer and can be ordered separately. This manual. Please give us your feedback on the quality of this documentation Name: Job Title: Organization: Address: If mailing to the address in the USA (see over), fill out this sheet. If mailing to the address in Spain, fill out the other sheet. Alternatively, you can fax this form to: Spain (34) 3 582 1400, Attn: Learning Products Dept. Phone: Circle the appropriate score Overall ease of use of this manual Overall ease of use of the Quick Reference Guide Cut here Poor 1 1 1 1 " 2 2 2 2 " 3 3 3 3 " 4 4 4 4 Excellent 5 5 5 5 Use of language in both documents Use of graphics in both documents Please explain any low score: Any other comments on any of the documentation accompanying the plotter: C4713-90021 Thank you AAA Any comments? B Fold here and then staple or tape the ends together B NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO. [. . . ]