User manual HP L1740 17-INCH LCD MONITOR

[. . . ] User Guide HP L1740 17" and L1940 19" Flat Panel Monitors Document Part Number: 372837-001 January 2005 This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. © Copyright 2005 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U. S. Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in the U. S. [. . . ] · If OSD is off, press to enable the DVI signal input (available on select models) 2 3 ­ (Minus) 4 + (Plus) · If OSD is on, press to navigate forward through the OSD menu features and increase adjustment levels. · If OSD is off, press to enable the VGA signal input. 5 Power Turns the monitor on or off. 4­4 User Guide Operating the Monitor Adjusting Monitor Settings Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. If the monitor is not already on, press the Power switch to turn on the monitor. Press the Menu button on the monitor's front panel to launch the OSD Main Menu. 3. To navigate through the OSD Menu, press the + (Plus) button on the monitor's front panel to scroll up, or the ­ (Minus) button to scroll in reverse. To select an item from the OSD Menu, use the + or ­ buttons to scroll to and highlight your selection, then press the Menu button to select that function. Adjust the item using the + or ­ buttons on the front panel to adjust the scale. User Guide 4­5 Operating the Monitor 6. After adjusting the function, select Save and Return, or Cancel if you don't want to save the setting, then select Exit from the Main Menu. 10 seconds If the buttons remain untouched for saved whenwhile displaying a menu, the new adjustments will be the OSD automatically times out and exits the menu. Using the On-Screen Display There are two On-Screen Display menus available; one for basic adjustments, and one for advanced adjustments. To access the Basic OSD Menu, press the menu button on the monitor's front panel. Basic OSD Menu Levels Menu Level 1 Brightness Contrast Auto Adjustment Advanced Menu Exit Menu Level 2 Adjustment Scale Adjustment Scale To access the Advanced OSD Menu, press the menu button again, or select Advanced Menu from the Basic OSD Menu. Menu After selecting the Advanced defaultfrom the Basic Menu, the Advanced Menu remains the OSD on subsequent power-ups of the monitor until the Basic Menu is selected or Factory Reset is applied. 4­6 User Guide Operating the Monitor The Advanced OSD Menu has up to three sublevels and can be viewed in one of seven available languages. The following table provides the menus and their functions at each level: Advanced OSD Menu Levels Level 2 Level 3 Adjustment Scale Adjustment Scale Auto Adjustment Horizontal Position Vertical Position Clock Clock Phase Cancel Save and Return Color 9300 K 6500 K Custom Color sRGB Cancel Save and Return Language Deutsch S. Chinese English Espanol Francais Italiano Nederlands Cancel Save and Return Management Power Saver Power On Recall On / Off Selection On / Off Selection N N N N Custom Color Adjustment Y "Adjusting" Message Adjustment Scale Adjustment Scale Adjustment Scale Adjustment Scale Level 1 Brightness Contrast Image Control Factory Preset Y Y Y Y Y Y Y User Guide 4­7 Operating the Monitor Advanced OSD Menu Levels (Continued) Level 1 Level 2 Level 3 Factory Preset Mode Display Power-On Status Display Sleep Timer Default Video Input Serial Number Basic Menu Cancel Save and Return OSD Control Horizontal OSD Position Vertical OSD Position OSD Timeout Cancel Save and Return Information Current Settings Recommended Settings Serial Number Total Hours Backlight Hours Exit Factory Reset Exit Yes No Adjustment Scale Adjustment Scale Adjustment Scale N N N On / Off Selection On / Off Selection Timer Set Menu Analog - VGA Digital Display monitor s/n N N N N N 4­8 User Guide Operating the Monitor Adjusting Screen Quality Allow the monitor to warm up for 20 minutes before performing the following procedures. The Auto-adjustment feature automatically fine-tunes the image quality each time a new video mode is utilized. If additional improvement is desired, press the Auto adjust button on the front bezel. For more precise adjustments, use the adjustment pattern utility provided on the CD, and adjust the clock and phase settings (accessed from the OSD menu) as described in the following section. Optimizing Analog Video This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor. Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock Phase. Use these controls only when the auto-adjust function does not provide a satisfactory image. set correctly since the Clock The Clock must first beon the main Clock setting. Phase settings are dependent Clock--Increase/decrease the value to minimize any vertical bars or stripes visible on the screen background. Clock Phase--Increase/decrease the value to minimize video distortion or video jitter. controls, you will best When using thepattern application obtain theon theresults by using the adjustment provided CD-ROM. User Guide 4­9 Operating the Monitor the Clock and Clock Phase monitor When adjusting distorted, continue adjustingvalues, if theuntil the images become the values distortion disappears. [. . . ] Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call1 1-800- 652-6672 For questions regarding this FCC declaration, contact: Hewlett Packard Company P. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product. C­2 User Guide Agency Regulatory Notices Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards): EN55022 (CISPR 22) - Electromagnetic Interference EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) - Electromagnetic Immunity EN61000-3-2 (IEC61000-3-2) ­ Power Line Harmonics EN61000-3-3 (IEC61000-3-3) ­ Power Line Flicker EN60950 (IEC950) - Product Safety User Guide C­3 Agency Regulatory Notices Japanese Notice Korean Notice EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Hewlett Packard Company has determined that this product meets the Energy Star guidelines for energy efficiency. [. . . ]