User manual HP M1722B CODE MASTER XL+

[. . . ] M1722B CodeMaster XL+ Defibrillator/Monitor User's Guide QhIH &!!(#(' QvrqvVT6Er! @qvv" Notice About This Edition Publication number M1722-94980 Edition 3 Printed in USA The information in this guide applies to the CodeMaster XL+ defibrillator/monitor. This information is subject to change without notice. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Authorized EU-representative: Hewlett-Packard Deutschland GmbH Herrenbergerstrasse 130 D-71034 Boeblingen Germany Fax: +49-7031-14-2346 Hewlett-Packard assumes no liability for failures resulting from RF interference between HP medical electronics and any radio frequency generating equipment at levels exceeding those established by applicable standards. CAUTION Warranty Hewlett-Packard makes no warranty of any kind with regard to this material, included, but not limited to, the implied warranties or merchantability and fitness for a particular purpose. [. . . ] Do not use a damaged sensor or one with exposed electrical circuits. Patient Movement Make sure that the application site chosen does not move excessively, which may adversely affect the performance of the sensor. You may have to replace the sensor to ensure good adhesion, or you may have to choose another application site. Inspecting the Application Site Inspect the SpO2 sensor site at least once every 2 hours to ensure adhesion, skin integrity, and correct alignment of the light emitter and photodetector. Should alterations of skin integrity occur, remove the sensor and reapply at another recommended site. Avoid application of the sensor to edematous or fragile tissue. Check circulation distal to the sensor site routinely. Circulation at Application Site Wrapping the tape too tightly, or using supplemental tape, can cause venous pulsations that could potentially lead to inaccurate saturation measurements. Therefore, do not wrap the adhesive too tightly and do not use additional tape to 6-5 TP HvvtPvhy VvtTP HvhQhvr secure the sensor. High positive intrathoracic airway pressures, valsalva maneuvers, or other consequences of impaired venous return may also cause venous pulsations. Only use adhesive wraps recommended by Hewlett-Packard. Avoid placing the SpO2 sensor on any extremity with an arterial catheter, blood pressure cuff, or intravascular venous infusion line. Connect the Sensor to the CodeMaster XL+ When you have applied the sensor to the patient, plug the disposable and semidisposable sensors into the connector cable and plug this cable into the SpO2 socket on the lower right of the CodeMaster XL+. Plug the M1190A sensor directly into the SpO2 socket of the CodeMaster XL+. The plug is keyed and is color-coded blue to distinguish it from the white ECG socket. Avtr%" TP v 8rpvturTP Trur8qrHhrYG 6-3 6-6 TP HvvtPvhy VvtTP HvhQhvr 8 6V UD PI Do not force the SpO2 connector into the ECG input socket. Doing so may damage the pins on the cable connector. Start Monitoring Turn the defibrillator on, if necessary, by turning the Energy Select control to Monitor On. Press the right corner of the display. TP PPss button to display the SpO2 reading in the upper SpO2 Readings Avtr%# HR LEAD I I TP rhqvt SPO2 PR 72 Qyrhr Qyrhyvqrvqvph 8qrHhrYG9vyhvuTP Srhqvt 6-4 The pulse amplitude indicator shows the quality of the SpO2 signal. Since it is derived from the patient's plethysmograph signal, it varies with the pulse of the 6-7 TP HvvtPvhy TP 6yh patient. If the patient has a very low signal the pulse amplitude indicator does not vary through its full range. If the signal is noisy, the pulse amplitude indicator does not vary rhythmically with the pulse. The pulse rate is derived from the pulse oximeter. It should correlate closely with the patient's heart rate. 6SpO 2 Alarms Activating SpO2 Alarms There are three preset high/low SpO2 alarm limits: 100/90, 100/85 and 100/80. Press the button repeatedly to cycle through the alarm options and the no alarm option. [. . . ] The recorder can be configured to run in either real time or with a sixsecond delay. Frequency Response: 0. 5 to 40 Hz or 0. 05 to 150 Hz selectable. Size and Weight Dimensions: 7. 9 in H by 11. 8 in W by 15. 6 in L (20 cm H by 30 cm W by 39. 7 cm L). Includes external paddles, battery, and recorder paper. A-16 DhyyhvhqTr Trpvsvphv Battery Type: Rechargeable sealed lead-acid battery. Charge Time: 2 hours to 90% of full capacity. [. . . ]