User manual HP PAVILION MEDIA CENTER TV M7685 QUICK SETUP

[. . . ] (Lower the volume before you start a CD-ROM audio program to protect your hearing and the audio speakers. ) LED indicators: The drive features two LED indicator lights on the front panel. Various operations are indicated as per the following table: Operation At tray loading At tray eject During write/erase During audio play During seek/data transfer Right LED green LED flashes green LED flashes off green LED flashes green LED lights Left LED off off green LED flashes off off emergency eject mechanism: If the eject button fails, you can turn off the power to the CD-RW drive and insert a small, thin rod (such as a straightened paper clip) into the emergency eject mechanism opening and press firmly to eject the disc. Caution: Do not attempt to use the emergency eject mechanism when either the Power or Busy indicator is lit or you may seriously damage the disc or the CD-RW Drive. eject button: Press this button to open or close the disc tray. [. . . ] interface connector: Use an IDE interface ribbon cable to connect the CD-RW drive to an IDE interface in your computer. power connector: Connect the power connector to the +5VDC and +12VDC power sources. The +5VDC terminal is on the left as you face the rear panel; the +12VDC terminal is on the right. The two center terminals are ground terminals. This is a ground connection for the CD-RW Drive. Configuring the CD-RW Drive The Master/Slave/CSEL jumper configuration of your TEAC CD-RW drive will depend on whether or not you have an IDE CD-ROM/DVD drive installed in your system. The following section will guide you through most typical system configurations. jumper set to CSEL jumper set to Slave jumper set to Master (default) 3 TEAC CD-RW Installation Guide Installing the CD-RW Drive Installing the CD-RW Drive This section explains how to install the TEAC CD-RW Drive into an IBM PC or compatible personal computer. Follow the steps below and refer to your computer documentation for information specific to your system. Turn off the power to the computer system and any external devices connected to it. Touch the exposed metal frame of the computer to ground yourself. This will prevent damage to the computer or CD-RW drive that may be caused by a discharge of static electricity. Remove your computer's cover, faceplate, or 5. 25-inch bay cover, as well as mounting clips, screws, and retaining brackets. (If your original cable does not have an available middle connector, you will need to acquire and install a standard IDE cable with three connectors. ) 5d) Your CD-ROM/DVD drive probably uses an audio cable that is connected to the computer's sound card. Therefore, there is no need to connect an audio cable to your CD-RW drive. An audio cable is not necessary for recording audio CDs. Connect the power cable to the power connector on the rear panel of the CD-RW drive. Insert the power cable plug in the correct orientation into the power connector. The plug is shaped so that it can be easily inserted in only one orientation; do not force the plug into the connector. The +5v terminal is on the left as you face the rear of the panel; the +12v terminal is on the right. The two center terminals are ground terminals. TEAC CD-RW Installation Guide 5 Recommended Software 7. 8. Re-install your computer's cover, faceplate, or bay cover. Start your system. Notes: · The IDE CD-RW drive is a true Plug-N-Play device; therefore, it will be detected automatically by Windows 95/98/Me/2000-Professional. There is no need to install any drivers. [. . . ] At the "Select a SCSI Adapter Option" window, select "IDE CD-ROM DRIVE (ATAPI Ver 1. 2). " Click "Install" and follow the instructions on screen. The drive is recognized by the operating system as a typical CD-ROM drive. Once you confirm that you can read (play) data discs from the CD-RW drive, install the premastering software to enable recording to CD-R and CD-RW discs. The premastering software is to be purchased separately. · · · Recommended Software Before you can record data onto CD-R or CD-RW discs using your TEAC CD-RW Drive, you must first install pre-mastering or packet-writing software onto your computer's hard disk. [. . . ]