User manual HP PAVILION W5171 UPGRADING AND SERVICING GUIDE

[. . . ] Reverse engineering or disassembly is prohibited. 4, 631, 603, 4, 577, 216, 4, 819, 098, and 4, 907, 093 licensed for limited viewing uses only. Registered trademarks of Microsoft Corporation. HP supports lawful use of technology and does not endorse or encourage the use of our products for purposes other than those permitted by national copyright law. ® Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Also, make sure you have the correct software and drivers for the optical drive to work with the operating system. ® A Upper optical drive bay, may be a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive B Lower optical drive bay, may be empty (blank plate) or a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive C Memory card reader (select models) D Diskette (floppy) drive (select models) E Front connector panel (no replacement instructions) F Hard disk drive G Second hard disk drive (select models) Upgrading and Servicing Guide 3 Removing a Drive 1 Complete the procedures to prepare the PC, to remove the side panel, and to remove the front panel. See "Opening and Closing the PC" on page 1. 2 Locate the drive you want to remove. 4 Disconnect the power cable and data cable from the back of the drive you want to remove, as indicated in the following illustrations: · For optical drives, disconnect the power cable (P) and the data cable (D) from the back of the drive you want to remove. If the drive has a sound cable (S), disconnect it also. · For most drive cables, use a gentle rocking motion to free the plug. For Serial ATA hard disk drive cables, press the latch (5) (select models only) in the center of each plug and pull the plug (6) from the drive connector. 3 Release the drive from the chassis by lifting the tab (1) on the latch drive bracket, and then sliding (2) the drive partway out of the bay. (The latch drive bracket secures the drives in their respective positions in the chassis. ) For a second hard disk drive, remove the two screws (3) and then slide the drive part way back out of the bay (4). Disconnecting the Optical Drive Cables Disconnecting the Memory Card Reader Drive Cable Disconnecting the Diskette (Floppy) Drive Cables Removing the Second Hard Disk Drive 4 Upgrading and Servicing Guide 6 5 Disconnecting the Serial ATA Hard Disk Drive Cables 3 Make sure the jumper on the new optical drive or new Parallel ATA hard disk drive is in the CS (Cable Select) position. Your drive may vary from the illustration. The Serial ATA hard disk drive does not use Cable Select. CS SL MA Disconnecting the Parallel ATA Hard Disk Drive Cables Cable Select Jumper 5 Pull the drive out of the drive bay. 6 If you are replacing the old drive with a new drive, remove the four guide screws (two on each side) from the old drive. You need these screws to install the new drive. 4 Install four guide screws on the sides of the new drive (two on each side). The screws help guide the drive into its proper position in the bay. For a second hard disk drive, skip this step and go to step 5. 5 Slide the drive part way into the drive bay, making sure to align the guide screws with the guide slots. Replacing or Adding a Drive 1 If necessary, remove the existing drive. See "Removing a Drive" on page 4. 2 If you are adding a drive to an empty lower optical drive bay, you must remove the blank plate from the bay. To do so, insert a flat screwdriver into the blank plate slot (C) and rotate the screwdriver to break the blank plate out of the chassis. Discard the blank plate. Upgrading and Servicing Guide 5 For a second hard disk drive, slide the drive into the bay (with connectors facing out) and align the screw holes (3). Insert the two screws (4). Connecting the Memory Card Reader Drive Cable Connecting the Diskette (Floppy) Drive Cables 6 Reconnect the power and data cables to your drive as indicated in the following illustrations. If it is present, reconnect the sound cable. Connecting the Serial ATA Hard Disk Drive Cables Connecting the Optical Drive Cables NOTE: An optical drive may include a sound cable. Connect this cable also. 6 Upgrading and Servicing Guide Adding Memory Your PC comes with random access memory (RAM), which temporarily stores data and instructions on your PC. The PC ships with one or more memory modules, but you can replace the existing memory module(s) with higher-capacity ones. [. . . ] See "Opening and Closing the PC" on page 1. 3 Remove any cabling, if necessary, to reach the battery. 4 Remove any memory modules, if necessary, to reach the battery. See "Adding Memory" on page 7. [. . . ]