User manual HP STORAGE INTEGRATION UTILITY SOFTWARE

[. . . ] HP StorageWorks Management Pack for System Center Operations Manager 2007 installation and user guide Part number: T4282-96002 Second edition: May 2007 Legal and notice information © Copyright 2004-2007 Hewlett-Packard Development Company, L. P. Valid license from HP required for possession, use or copying. Consistent with FAR 12. 21 and 12. 212, Commercial 1 Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U. S. Government under vendor's standard commercial license. [. . . ] Configure the SNMP trap generator on the Command View server. Configure the Command View storage environment hosts, to send the SNMP traps to the OpsMgr 2007 server. Getting SNMP traps from VA To get SNMP traps from VA, make following changes: In Linux To get SNMP traps from VA, complete the following steps: 1. Open the following file: /opt/sanmgr/commandview/server/config/PanConfigParams. txt 2. Enter the following command: SNMPTRAP_DEST=<IPs of machines to which traps must be sent, separated by comma> In Windows To get SNMP traps from VA, complete the following steps: OpsMgr 2007 23 1. Open the following file: C:\Program Files\HewlettPackard\Sanmgr\CommandView\Server\ Config\PanConfigParams. txt 2. Enter the following command: SNMPTRAP_DEST=<IPs of machines to which traps must be sent, separated by comma> In HP-UX To get SNMP traps from VA, complete the following steps: 1. Open the following file: /opt/sanmgr/commandview/server/config/PanConfigParams. txt 2. Enter the following command: SNMPTRAP_DEST=<IPs of machines to which traps must be sent, separated by comma> NOTE: The SNMP Trap Catcher receives traps from Virtual Array management software (Command View SDM), Tape Library Management Software (Command View TL), and XP Disk Array Management software, (Command View XP) and processes the OpsMgr 2007 events. Installing the Management Pack software The Management Pack software and documentation are bundled in a HP Management Pack for Systems Center Operations Manager 2007. zip file. This file is located at the following website: www. hp. com/go/storageworks/scom2007 The HP Management Pack for Systems Center Operations Manager 2007. zip file, contains the following files: · Installation and User Guide · SCOM Management Server. zip · HP StorageWorks WEBES Listener for MOM 2005 And SCOM 2007. zip Each zip file contains the following files: · setup. ini · setup. exe · an appropriate. msi file 24 Installing Management pack Installing WEBES Listener on WEBES Collection Point Systems From the HP StorageWorks WEBES Listener for MOM 2005 and OpsMgr 2007. zip file, extract and install the HP StorageWorks WEBES Listener for MOM 2005 and OpsMgr 2007. msi file on any system you plan to use as a WEBES collection point. Figure 10 WEBES Event Flow to collection points Complete the following steps on each system that you plan to use as a WEBES Collection Point: 1. Ensure that the. msi file is available to the systems that are to be configured as WEBES collection points. Unzip the file. OpsMgr 2007 25 3. Double-click the msi file, or run setup. exe. The Storage Management Pack setup wizard displays, as shown in Figure 1 1. Figure 1 Management Pack Setup Wizard Screen 1 4. The Confirm Installation window displays as shown in Figure 12. Figure 12 Confirm Installation 26 Installing Management pack 5. The Installing HP Enterprise Storage Management Pack window displays, as shown in Figure 13. Figure 13 Installing HP Enterprise Storage Management Pack 6. The Installation Complete window displays, as shown in Figure 14. Figure 14 Installation Complete 7. Click Close. Installing the Management Pack software on the OpsMgr 2007 Management Station To install the HP StorageWorks Management Pack for SCOM. msi file on the system that you have designated as a OpsMgr 2007 Management Server, complete the following steps: 1. Unzip the HP Management Pack for Systems Center Operations Manager 2007. zip file. Navigate to the unzipped folder, and run setup. exe or double-click on the. msi file. This starts the Installation wizard, as shown in Figure 15. OpsMgr 2007 27 3. Click Next to continue. Figure 15 Management Pack setup wizard 4. Click Next to confirm the installation, as shown in Figure 16. Figure 16 Confirm installation 28 Installing Management pack 5. [. . . ] The port number needs to be the same in both the WEBES desta mom configuration and the OpsMgr 2007 Management Pack configuration. "Configuring WEBES to send an XML event callout" contains instructions for changing the port you are using; be sure both of the configurations are using the same port. The systems running WEBES Event Listener when discovered are not getting displayed in the Discovered Inventory pane. Ensure that you have selected the right computer group and then refresh the Monitoring pane. [. . . ]