User manual HP STORAGEWORKS 12000 VIRTUAL LIBRARY SYSTEM EVA GATEWAY STORAGEWORKS 12000 GATEWAY VIRTUAL LIBRARY SYSTEM INSTALLATION (AH814-96102, AP

[. . . ] Keep parts in their containers until needed. Ensure that you are properly grounded when touching static sensitive components. © Copyright 2007 Hewlett-Packard Development Company, L. P. First edition: August 2007 The information in this document is subject to change without notice. Printed in the US www. hp. com Rack requirements HP supports the HP System E racks and the HP 10000 Series racks for use with the virtual library system (VLS). [. . . ] Locate four MS screws and insert each one into a square, semi-pierced washer (included). NOTE: This rail kit includes pan-head screws and MS screws. At one side of each rack, align the front rail holes with the corresponding holes in the back of the rack. Secure by inserting two of the provided MS screws and semi-pierced washers through the holes in the rack, which correspond to the two outermost holes in the rail, then through the holes in the rail itself. 11193 a. Align the inner rail with the switch so that the perpendicular screw hole faces away from the switch but is parallel to the switch bezel (face-plate). The two holes at the front of the rail must align with the two holes at the front of the switch. Insert two of the pan-head screws through the slide rail and into the switch at the front of the switch. Insert two of the pan-head screws through the appropriate holes in the slide rail and into the switch at the back of the switch. Perform these steps again to install the other rail on the other side of the node. 10 Installing the switch 2824 in the rack a. Align the rails on the node with the rails on the rack. The rails on the node will lock into the rails on the rack. On each side of the switch, insert an MS screw through the holds in the rail and into the holes in the rack. Tighten the MS screws to secure the switch to the rack. 11194 d. At the front of the rack, slide the clip onto the rack so that the hexagonal hole is facing out and align the holes in the clip with the proper hole in the rack. Then align the rail hole with these holes. 2 1 11195 e. f. Push the screw through the rail, clip, and rack, then into the nut. Using a #2 Phillips screwdriver, tighten the screw to secure the rail to the rack. Repeat for the opposite rail. Page 4 j. 1 Installing cables on the primary node 1 of the VLS12000 Gateway 1 2 3 4 5 6 12 Begin routing the cables through the cable ties that shipped with the racks. 12 Installing cables on the secondary nodes of the VLS12000 Gateway NOTE: Use this procedure to install secondary nodes: node 1 (shipped with the gateway) or upgrade nodes 2-7 (ordered separately). 11 10 9 8 7 11488 1 2 3 4 5 6 7 8 9 10 1 1 12 Quad port FC card, storage port, port 3 Quad port FC card, storage port, port 2 Quad port FC card, host port, port 1 Quad port FC card, host port, port 0 Power supply 2 Power supply 1 NIC2, on primary node connects to port 1 of switch 2824 NIC1, on primary node connects to the external network Keyboard connector Video connector Serial connector to access CLI USB connector, on primary node connects to USB/Ethernet adapter, then to port 1 of switch 2524 1 2 3 4 5 6 7 8 8 1 2 3 4 5 6 7 11489 Quad port FC card, storage port, port 3 Quad port FC card, storage port, port 2 Quad port FC card, host port, port 1 Quad port FC card, host port, port 0 Power supply 2 Power supply 1 NIC2, on secondary nodes connects to the next available port of switch 2824 USB port, on secondary nodes connects to USB/Ethernet adapter, then to the next available port of switch 2524 a. Connect one end of an Ethernet cable (not provided) to NIC1. Connect the other end of the cable to the existing external network b. Connect one end of an FC cable (not provided) to host port 0. Connect the other end to an external FC switch/fabric that connects to your tape backup hosts. [. . . ] Connect the other end to a second external FC switch/fabric that connects to your external array. Connect one end of an Ethernet cable to NIC2. Connect the other end of the cable to port 2 of switch 2824. Connect one end of a USB cable to the USB port. [. . . ]