User manual HP STORAGEWORKS 2000I MODULAR SMART ARRAY

[. . . ] HP StorageWorks 2012i Modular Smart Array user guide Part number: 481598-001 First edition: March, 2008 Legal and notice information © Copyright 2008 Hewlett-Packard Development Company, L. P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright. [. . . ] SMU enables you to view the software, hardware, and other version information for each controller and the enclosures. To view controller version information, select Monitor > Status > Advanced Settings > Controller Versions. To view drive enclosure information, select Manage > Update Software > Enclosure Firmware > Show Enclosures. For software and firmware updates, go to http://www. hp. com/go/msa. Select MSA SAN Arrays, select your product, and go to Support. Setting the Date and Time You can set the date and time manually or configure the system to use Network Time Protocol (NTP) to obtain them from a network-attached server. When NTP is enabled, and if an NTP server is available, the system time and date can be obtained from the NTP server. This allows multiple storage devices, hosts, log files, and so forth to be synchronized. 50 HP StorageWorks 2012i Modular Smart Array user guide · March 2008 NTP server time is provided in Universal Time (UT), which provides several options: If you want to synchronize the times and logs between storage devices installed in multiple time zones, set all the storage devices to use UT. If you want to use the local time for the device, set its time zone appropriately. If a time server can provide local time rather than UT, configure the storage devices to use that time server, with no further time adjustment. If no NTP server is present, the date and time are maintained as if NTP had not been enabled. To manually set the system date and time: 1. Select Manage > General Config > Set Date/Time. In the Set System Date panel, select the current month, day, and year. In the Set System Time panel, type time values using a 24-hour clock (where hour 8 represents 8 a. m. and hour 20 represents 8 p. m. ) and select the proper time zone. To obtain the date and time from an NTP server: 1. Select Manage > General Config > Set Date/Time. In the Obtain Time With NTP panel, set Network Time Protocol to Enable and optionally type the IP address of an NTP server. If no IP server address is set, the system listens for time messages sent by an NTP server in broadcast mode. In the Set System Time panel, select the proper time zone. You might have to refresh the page to display updated values from the NTP server. Chapter 4 Configuring a System for the First Time 51 Configuring Controller Enclosure Host Ports To configure iSCSI host ports on the controller enclosure, complete the following steps: 1. Select Manage > General Config > Host Port Configuration. In the Controller Module Host Port Configuration panels, for each host port on controller A and controller B, enter the following values: IP address. [. . . ] A begy jtés pontos helyér l b vebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat. 76 HP StorageWorks 2012i Modular Smart Array user guide · March 2008 Italian Notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche. La raccolta differenziata e il corretto riciclo delle apparecchiature da smaltire permette di proteggere la salute degli individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta delle apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio presso il quale è stato acquistato il prodotto. Latvian Notice Nolietotu iek rtu izn cin sanas noteikumi lietot jiem Eiropas Savien bas priv taj s m jsaimniec b s S ds simbols uz izstr d juma vai uz t iesai ojuma nor da, ka so izstr d jumu nedr kst izmest kop ar citiem sadz ves atkritumiem. [. . . ]