User manual HP STORAGEWORKS 6100 ENTERPRISE VIRTUAL ARRAY

[. . . ] HP StorageWorks IP Distance Gateway user guide Part number: 5697-7120 Third edition: November 2007 Legal and notice information © Copyright 2007 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. [. . . ] This setting allows the user to limit the bandwidth used by the FCIP route so as to not consume all the available link bandwidth. IP Distance Gateway user guide 83 For example if the slowest link in the WAN being used is a DS-3 link then the maximum available bandwidth is 45 megabits per second. To limit the FCIP route to 33% of the overall link bandwidth set the bandwidth to 15 megabits per second. After setting the FCIP parameters, click Next to continue. The Security Check dialog box requests the administrator password; see Figure 42. Enter the appropriate password, then click OK to confirm the add of the FCIP route. Figure 42 FCIP route add Wizard--security check dialog box 7. The Add FCIP Route Complete dialog box signifies the completion of the route add operation; see Figure 43. This dialog box may take a number of seconds before appearing. Click OK to exit the dialog box. Figure 43 FCIP route add Wizard--completed dialog box FCIP route remove The FCIP Route Remove Wizard provides step-by-step instructions for removing a FCIP route. When the FCIP route remove Wizard launches, a warning is displayed cautioning that the operation about to be performed will change the operation of the selected GE and FC ports. Also connectivity on the GE port not part of the FCIP route being removed will be momentarily disrupted. If you want to proceed, click Yes and continue with step 2. Otherwise, click No to cancel the Wizard. 84 Using the HP StorageWorks mpx Manager Utility Figure 44 FCIP route remove Wizard--warning dialog box 2. Enter the FCIP route to be removed per the Route Remove Selection dialog box; see Figure 45. Figure 45 FCIP route remove Wizard--route selection dialog box 3. Enter the administrator password per the Security Check dialog box. IP Distance Gateway user guide 85 4. Click OK to confirm the removal of the FCIP route. The Remove FCIP Route Complete dialog box indicates the completion of the route remove operation; see Figure 46. Click OK to exit the dialogue box. Figure 46 Remove FCIP route complete message 86 Using the HP StorageWorks mpx Manager Utility A Command line interface CLI summary This appendix includes the following: · · · · Logging on to the mpx1 10, page 87 User accounts, page 87 Working with SAN mpx1 configurations, page 88 10 Commands, page 90 Logging on to the mpx1 10 To log on to an mpx1 using Telnet, open a command line window on the workstation, 10 and then enter the Telnet command followed by the mpx1 IP address: 10 # telnet ip-address A Telnet window opens prompting you for a login. To log on to a switch through the serial port, configure the server port with the following settings: · · · · 1 15200 baud 8-bit character 1 stop bit No parity User accounts The mpx1 ships with the following user account already defined: 10 Account name: Password: guest password See "Password command" on page 100 for more information about changing passwords. IP Distance Gateway user guide 87 Working with SAN mpx1 configurations 10 Successful management via the CLI depends on the effective use of mpx1 10 configurations. Modifying configurations, backing up configurations, and restoring configurations are key management tasks. Modifying a configuration The two major areas that require configuring include management port configuration and FCIP Route configuration: Management port configuration uses the following commands: · Set Mgmt · Show Mgmt FCIP Route configuration uses the following commands: · fciproute add · fciproute mod · show fciproutes 10 Saving and restoring mpx1 configurations 10 See Saving and restoring the mpx1 configuration, page 169 for commands related to backing up and restoring a configuration. Saving mpx1 configuration and persistence 10 Perform the following steps to save the configuration and persistent data. Persistent data consists of LUN mappings, discovered FC targets, and discovered iSCSI initiators. Execute the Fru save CLI command (see FRU Command) to generate a file (HP_StorageWorks_mpx1 10_FRU. bin) containing the saved data. This file is stored locally on the mpx1 in an FTP directory. [. . . ] If the product is to be used in another country, purchase a power cord that is approved for use in that country. The power cord must be rated for the product and for the voltage and current marked on the product electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 1. 00 mm2 or 18 AWG, and the length of the cord must be between 1. 8 m, (6 ft) and 3. 6 m (12 ft). [. . . ]