User manual HP VISUALIZE J2240 WORKSTATION

[. . . ] J282/2240 Owner's Guide R Workstation Systems Group HP Part No. A2876­90015 Edition E1297 Printed in U. S. A. © Hewlett-Packard Co. 1997 First Printing: December 1997 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. HEWLETT­PACKARD WARRANTY STATEMENT HP PRODUCT DURATION OF WARRANTY J282/J2240 one year 1. [. . . ] Jumper information for each drive is included in these steps. NOTICE: Before opening the system unit, follow the instructions in "Checking the SCSI IDs, " earlier in this appendix, to determine the SCSI IDs currently in use on your workstation. 1. Open the system unit according to the directions in "Opening the System Unit, " earlier in this appendix. Unscrew the two captive screws on the left side of the Storage Assembly and pull down the drawer ejector handle on the right side of the Storage Assembly, as shown in Figure B­3. The Storage Assembly slides partway out of the drawer. 2. B-10 1st Captive Screw (2nd Captive screw is below 1st, but not visible in this view) Drawer Ejector Handle Figure B­3. Removing Storage Drawer from System Unit 3. Pull the Storage Assembly out as far as it will go. (A safety catch prevents the drawer from coming all the way out. ) When sliding the Storage Assembly out of the system unit, move the drawer ejector handle to prevent the Storage Assembly from hitting it. NOTICE: 4. Push in on the safety catch and continue pulling the drawer out. Be sure to support the drawer from the bottom. B-11 5. 6. Set the drawer on a flat surface. Disconnect the power distribution cable from the Fan extender cable. Power Extender Power Distribution Cable Figure B­4. Removing FAN from EMI Plate 7. B-12 Disconnect the Fan extender cable form the SCSI PCA. M3 Screw M3 Screw Figure B­5. Removing EMI Plate 8. Remove the two M­3 screws from the fan. B-13 Figure B­6. Removing FAN/EMI Plate 9. Unscrew the captive screw holding the FAN/EMI plate at the back of the removable drives and lift the plate up and out of the drawer, as shown in Figure B­6. 10. Disconnect the SCSI and power cables from the drive. B-14 11. Unscrew the two screws holding the drive in the storage drawer, and slide the drive out of the drawer. See Figure B­7. Figure B­7. Removing Drive Screws 12. Check the SCSI address/jumper settings on the replacement drive, using the following information sections. B-15 CD-ROM Drive The CD-ROM drive ships with the drive set to SCSI ID address 2. We recommend keeping the address setting at 2 unless it is used by another device. CAUTION: CD-ROM drives are susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static-grounding wrist strap that came in the CD-ROM drive kit. If you need to change the CD-ROM drive's address, follow these instructions, referring to Figure B­8. If you do not need to change the drive's address, go to Step 10 of this installation procedure. Locate the jumpers at the back of the CD-ROM drive. To change the address, use needlenose pliers to set the drive's SCSI ID to an address that is not used by another SCSI device. Check that the other jumpers are set correctly. Do not use SCSI ID 7 for your CD-ROM drive's SCSI address. The host SCSI controller uses SCSI ID 7. NOTICE: 3. Use needlenose pliers to remove the SCSI terminators, if still attached to the drive. B-16 SCSI ID 0 1 2 default SCSI ID 4 5 6 3 Figure B­8. CD-ROM Drive SCSI Address/Jumper Settings B-17 DDS Tape Drive The DDS tape drive ships with the drive set to SCSI ID address 3 and the Operation Mode switches set for correct drive operation. We recommend keeping the address setting at 3 unless it is used by another device. CAUTION: SCSI tape drives are susceptible to mechanical and electrostatic shock. [. . . ] Enter your user ID during the login procedure when the system displays the login prompt. See also user account. GL-22 username The name that the system recognizes as uniquely yours. The username is also the name that identifies you to the mail system and other software requiring secure entry. utility See utility program. utility program A program provided with the operating system to perform a frequently required task, such as printing a file or displaying the contents of a directory. See also command, shell command. window A rectangular area of the screen for viewing information. [. . . ]