User manual HUBBELL LIGHTING CH-ENC-23

[. . . ] اﻗﺮأ ﺑﺤﺮص اﻟﺘﻌﻠﻴﻤﺎت: ﺗﺤﺘﻮي ﻋﻠﻰ ﻣﻌﻠﻮﻣﺎت ﻫﺎﻣﺔ ﺣﻮل ﺗﺮﻛﻴﺐ واﺳﺘﻌﻤﺎل‬ ‫وﺳﻼﻣﺔ اﻟﻐﺴﺎﻟﺔ. ‬ ‫!ﺗﺠﺪ ﻓﻲ اﻟﻈﺮف اﻟﺬي ﻳﺤﺘﻮي ﻋﻠﻰ ﻫﺬا اﻟﻜﺘﻴﺐ أﻳﻀﺎ ﺷﻬﺎدة اﻟﻀﻤﺎن وﺑﻌﺾ‬ ‫اﻟﺘﻔﺎﺻﻴﻞ اﻟﻼزﻣﺔ ﻟﻌﻤﻠﻴﺔ اﻟﺘﺮﻛﻴﺐ. ‬ ‫‪AR‬‬ ‫ﺗﻮﺻﻴﻞ اﻟﻤﺎء واﻟﻜﻬﺮﺑﺎء‬ ‫ﺗﻮﺻﻴﻞ أﻧﺒﻮب اﻟﻤﺪ ﺑﺎﻟﻤﺎء‬ ‫!ﻗﺒﻞ وﺻﻞ أﻧﺒﻮب اﳌﺪ ﺑﺎﳌﺎء ﺑﺸﺒﻜﺔ اﳌﻴﺎه، اﺗﺮك اﳌﺎء ﻳﺠﺮي إﻟﻰ أن ﻳﺼﺒﺢ‬ ‫ﺻﺎﻓﻲ. ‬ ‫1. أوﺻﻞ أﻧﺒﻮب اﻟﻤﺪ ﺑﺎﻟﻤﺎء ﻣﻊ‬ ‫اﻟﻤﺎﻛﻴﻨﺔ ﻣﻦ ﺧﻼل ﻟ ّﻪ ﻋﻠﻰ ﻣﺄﺧﺬ‬ ‫ﻔ‬ ‫اﻟﻤﺎء اﻟﺨﺎص ﻟﻬﺬا اﻟﻐﺮض واﻟﻤﺘﻮاﺟﺪ‬ ‫ﺧﻠﻒ اﻟﻤﺎﻛﻴﻨﺔ ﻣﻦ ﺟﻬﺔ اﻟﻴﻤﻴﻦ )راﺟﻊ‬ ‫اﻟﺸﻜﻞ(. ‬ ‫ﻧﺰع اﻟﻐﻼف واﻟﺘﺴﻮﻳﺔ‬ ‫ﻧﺰع اﻟﻐﻼف‬ ‫1. [. . . ] Remove the 4 transit bolts used during transportation and the corresponding spacers on the back of the machine (see figure). A 3. Having removed the 4 bolts use the 4 plastic blanking plates to cover the 4 holes. Keep all the pieces; if the washing machine is transported in future, the transit bolts and spacers will have to be replaced in order to avoid damaging the inside of the machine. 2. Place the seal A (provided in the bag) on the end of the inlet hose and screw it to a cold water tap with a 3/4 BSP threaded connection (see figure). 3. Make sure there are no kinks or bends in the inlet hose.  Packaging materials should not be used as toys by children. Levelling  The water pressure at the tap must fall within the values indicated in the Technical data table (see next page). 1. Position the washing machine on a level and sturdy floor, without resting it against walls or cabinets. If the floor is uneven, the feet of the appliance may be adjusted until it reaches a perfectly horizontal position (the angle of inclination must not exceed 2 degrees).  If the water inlet hose is not long enough, contact a specialist store or an authorised technician. the machine.  Always use the new water inlet hoses supplied with  If the appliance is levelled correctly it will be more stable and much less likely to cause vibrations and noise during the spin cycle. 14 Drainage Connection  Do not use extension cables or multiple sockets. Connect the outlet hose to a draining duct or a stand pipe at a height between 65 and 100 cm from the floor. Do not bend it under any circumstances. GB  The cable should not be bent or compressed.  The cable should be replaced only by authorised technicians. Warning!The company shall not be held responsible for any incidents that occur if these regulations are not observed. 65 - 100 cm Alternatively, place the end of the hose over the edge of a washbasin or tub, fastening the hose supplied to the tap (see figure). value or to exclude the spin cycle completely: the value will be shown on the display. button: press to set a delayed start DELAY TIMER time for the selected programme. The delay time will be shown on the display. OPTION buttons: the name of the option will be shown on the display when the corresponding button is pressed. When the relevant indicator light illuminates, this shows that the option has been selected. INFO button: press the button to display information relating to the selected wash cycle and options. DELAY TIMER button indicator light WASH CYCLE PHASE icons: these light up to provide an indication of the progress of the wash cycle - Rinse - Spin - Pump out ). The (Wash lights up when the cycle has finished. text START/PAUSE button with indicator light: when the green indicator light flashes slowly, press the button to start the wash cycle. When the cycle has started, the indicator light is illuminated in a fixed manner. To pause the wash cycle, press the button again; the indicator light will turn orange and begin to flash again. If the “Door indicator light is off, the porthole door may Locked” be opened. [. . . ] The washing machines fails to fill with water. Possible causes / Solutions: • The plug has not been inserted into the electrical socket, or it has not been inserted far enough to make contact. • There is no power in the house. • The porthole door has not been shut properly. • The START/PAUSE button has not been pressed. [. . . ]