User manual HUBBELL LIGHTING EVRS ARMS

[. . . ] Çamaþýr makinesinin ambalajdan çýkartýlmasý 2. Çamaþýr makinesinin taþýma esnasýnda hasar görmemiþ olduðunu kontrol ediniz. Hasar görmüþ ise monte etmeyiniz ve yetkili satýcýyla temas kurunuz. Taþýma esnasýnda güvenliði saðlayan üç adet koruma vidasýný sökünüz ve üst kýsýmdaki plastik separatörü çýkartýnýz (resime bkz. ). 4. [. . . ] Yýkama iþlemi baþlamýyor. Muhtemel nedenler / Çözümler: • Fiþ prize takýlý deðil veya tam temas etmiyor. • Kapak iyi kapalý deðil (ýþýklý göstergede DOOR ibaresi görüntüleniyor). • Düðmeye • BAÞLAT/TEKRAR BAÞLATdüðmesine basýlmadý. • Su musluðu açýk deðil. • Baþlangýç zamanýný erteleme programlanmýþ (zaman ayarý, bkz. • • • • • • Su giriþ hortumu musluða takýlý deðil. Su musluðu açýk deðil. BAÞLAT/TEKRAR BAÞLAT düðmesine basýlmadý. Montaj Taným Çamaþýr makinesi su almýyor. (Iþýklý göstergede H2O ibaresi görüntüleniyor). Programlar Çamaþýr makinesi devamlý su alýp veriyor. • Boþaltma hortumu zeminden 65 ile 100 cm arasýnda yerleþtirilmemiþ (bkz. • Boþaltma hortumu suya girmiþ (bkz. • Duvardaki tahliyenin hava boþluðu yok. If this is the case, do not install it and contact your retailer. Remove the 3 protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure). 4. Seal the gaps using the plastic plugs provided. Use the plug provided to seal the three holes where the plug was housed, situated on the lower right-hand side on the rear of your appliance. Keep all the parts: you will need them again if the washing machine needs to be moved to another location. 1. Connect the supply pipe to the water mains using a gas 3/4 attachment, fitting the rubber gasket and the filter supplied with the appliance and ensuring that they are fimly tightened to the taps. The water supply marked C must be connected to the cold water tap; the pipe marked H must be connected to the hot water tap. Both pipes may be connected to the cold water tap using the special Y connection with multiple attachments, supplied with the appliance (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. Warning: clean the filters regularly by rinsing it under running water. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure). [. . . ] This is perfectly normal; Caring for your appliance door and drum • Always leave the appliance door ajar to prevent unpleasant odours from forming. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance. Checking the water inlet hose Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.  Never use hoses that have already been used. 22 Troubleshooting Your washing machine could fail to work. Before calling for Assistance (see page 24), make sure the problem can't easily be solved by consulting the following list. GB Installation Problem The washing machine won't start. [. . . ]