User manual HUMAX AVE-750

[. . . ] ** ** ** ** ** ** ** ** TABLE OF CONTENTS ** Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ** Safety Information: Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ** Tuner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Station Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] On the DSP menu, the choices are the DSP surround modes designed for use with two-channel stereo programs to create a variety of sound field presentations. The choices available are Hall 1, Hall 2 , Theater, Stadium, Classic, Panorama, Movie or Music. See page 25 for a complete explanation of the DSP surround modes. ** Figure 5 ** ** SYSTEM CONFIGURATION 18 ** ** ** ** ** ** ** ** ** ** ** ** 8 SYSTEM CONFIGURATION ** The first line of the SPEAKER SETUP menu (Figure 5) allows you to switch the menu to change either the underlying speaker size setting or the exact crossover point used for that speaker group. For the first pass through the menu, leave the setting at its default option of SIZE, and then proceed as outlined below. Once the speaker choices have been set you may wish to return to this line to change the option so that the crossover settings may be adjusted. Begin the speaker setup process by making certain that the LEFT/RIGHT line is highlighted in reverse video, which sets the configuration for the front left and right speakers. If you wish to make a change to the front speakers' configuration, press the / Navigation Buttons so that either LARGE or SMALL appears, matching the appropriate description from the definitions on page 19. When SMALL is selected, low-frequency sounds will be sent only to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the front channels. When LARGE is selected, a full-range output will be sent to the front left and front right outputs. Depending on the choice made in the SUBWOOFER line in this menu, bass information may also be directed to the front left/right speakers, a subwoofer or both. NOTE: When the front speakers are set to the LARGE option and the surround mode is set to "Surround Off, " or pure two-channel stereo, when an analog signal source is present it will be routed directly from the input to the volume control without being digitized or processed. If you have full-range front speakers and wish to remove all digital processing from the circuit path, select this configuration. If you wish to set this option for use with only one input, such as a CD player that uses an external DAC or an optional, external phono preamp, you may also wish to choose the INDIVIDUAL setting on the BASS MGR line at the bottom of this menu so that only those inputs where the analog bypass is desired will be routed in this fashion, while other analog inputs such as a VCR or cable box will be digitized for surround processing. When you have completed your selection for the front channel, press the Navigation Button to move the highlighted video to CENTER. Press the / Navigation Buttons to select the option that best describes your system, based on the definitions shown on page 18. When SMALL is selected, low-frequency surround channel sounds will be sent to the subwoofer output only. If you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround channel. When LARGE is selected, a full-range output will be sent to the center speaker output, and no center channel signal will be sent to the subwoofer output. When NONE is selected, no signals will be sent to the center channel output. The receiver will operate in a "phantom" center channel mode and center channel information will be sent to the left and right front channel outputs. When you have completed your selection for the center channel, press the Navigation Button to move the highlighted video to SURROUND. [. . . ] Unit does not respond to remote commands. · · ** ** · · · Weak batteries in remote Wrong device selected Remote sensor is obscured · · · ** ** ** ** Intermittent buzzing in tuner. Speaker Channel Input indicators flash and digital audio stops. · ** Local interference · ** · Digital audio feed paused · · ** Processor Reset In the rare case in which the unit's operation or the displays seem abnormal, the cause may involve the erratic operation of the system's memory or microprocessor. To correct this problem, first unplug the unit from the AC wall outlet and wait at least three minutes. After the pause, reconnect the AC power cord and check the unit's operation. [. . . ]