User manual HUSKY LINERS 47954

[. . . ] Check to insure you have received all the above listed Contents and that no damage has occurred during shipping. Package 8mm Allen Wrench T-50 Torx Wrench Phillips Head Screwdriver 1- Handle Assembly 2- 3/8"X 2-3/4" Hex Bolts 4- 3/8"X 1-1/2" Hex Bolts 1- Cargo Liner Retention Block 1- Cargo Liner 1- Drawer Liner (Foam) 2- 1" Round Spacers 2- 5" Long Nut Plates 3) Position Storage Box top side down, placing it on a flat, non-marring surface. Remove shipping blocks and Channel Iron from bottom of drawer using Phillips Head Screwdriver. Removing block will allow drawer to slide out so use caution and avoid tilting Drawer Unit. [. . . ] Turn handle and note the position of the cam latch. The cam latch should be 47954_Instruction Sheet. doc 09/11/2006 oriented on handle shank so that it will secure drawer unit when handle is horizontal on drawer (see note #2). Remove 3rd row seat(s) from vehicle and fold second row seats forward. 9) With cargo hatch open, remove the two cargo tie-down loops from the cargo area using a T50 Torx wrench. Position the two short 1" rounds spacers (provided) in the recesses where tie-down loops were removed. The storage box will later be positioned over these stand-offs and bolted into place. 10) Position a long nut plate (has 3 drilled/tapped holes) under each of the most forward 3rd seat brackets located on each side of the cargo area (see note #3). Note positioning of nut plate in the photo and situate nut plate accordingly with the stamped "F" on the nut plate toward the front of the vehicle. 11) Place the two provided 1/2" X 1" X 3-1/2" clamp plates over 3rd seat mounting rods, positioning them above each nut plate (see note #4). Note that clamp is positioned over the two drilled/tapped holes in the nut plate that are closest to the rear of the vehicle. 12) Insert two (2) of the 3/8" X 1-1/2" Hex Bolts and flat washers through each clamp, threading them into Nut Plates. Take care to insure that the Nut Plates/Clamps are positioned so that they will be pulled against both of the 3rd seat mounting rods when bolts are tightened (review positioning in note #4). 13) Remove Access Panel from rear of Storage Box using a 1/8" Allen Wrench. Carefully slide Storage Box into cargo area. 14) Position Channel Iron horizontally over the forward set of holes in the nut plate and insert the two (2) 3/8" X 2-3/4" Hex Bolts and flat washers through the 2 holes in the channel iron, threading them into Nut Plates (see note #5). 15) Insert the two, 4" pieces of strap so that one piece is centered under each end of the Channel Iron where Channel Iron contacts Storage Box (see note #5). 16) Install M10 X 60 Allen bolts and washers through case and 1" round spacers and into threaded holes that held tie-down loops. (It may be necessary to raise the front of the box to allow bolt to start) Tighten securely. [. . . ] The use or Armor All®, Son-of-a-Gun® or similar items is discouraged as the products make the liner slick. 22) Your Husky Storage Box comes with a limited one-year warranty. Winfield Consumer Products warrants its SUV Storage Box to be free from defects in material and workmanship of the product for one year, from the date of purchase, with proof of purchase. 47954_Instruction Sheet. doc 09/11/2006 Cam Latch Detent Pin Note #1-Removing Detent Pin Note #3--Showing placement and orientation of nut plate under seat mount brackets. Note #2-Position Handle so Cam Latch will be pointing up when handle is horizontal. Note #4--Showing placement and orientation of clamp plate over seat mount brackets and nut plate. 47954_Instruction Sheet. doc 09/11/2006 Note #5--Showing placement and orientation of Channel Iron and 4" Strap. [. . . ]