User manual HUSKY LINERS 5659

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUSKY LINERS 5659. We hope that this HUSKY LINERS 5659 user guide will be useful to you.

Lastmanuals help download the user guide HUSKY LINERS 5659.


Mode d'emploi HUSKY LINERS 5659
Download
Manual abstract: user guide HUSKY LINERS 5659

Detailed instructions for use are in the User's Guide.

[. . . ] PART NO. 5659 / 5656 FORD F-150 WITH FACTORY FENDER FLARES FORD F-150 WITHOUT FACTORY FLARES AND WITH FACTORY RUNNING BOARD FRONT MUD GUARD INSTALLATION INSTRUCTIONS Install Paint Protection Film before mud guards (see other side) Please read instructions thoroughly before installation. Tools Required · 1/8" drill bit / Drill · Short #2 Phillips screwdriver · Center punch Package Contents Driver & passenger side rear mud guard #10 screw (qty. 6) Paint Protection Film (1 set) Instruction sheet · · · · · NOTE: Turn the front wheels all the way to the left or right for mud guard installation. [. . . ] Remove existing fasteners from locations B and C (Figure 2). Attach mud guard to front fender with existing fasteners at locations B and C. Make sure bottom edge of mud guard is parallel to the ground before tightening fasteners. Using mud guard as a template, mark, center punch, and drill 1/8" holes at locations A and D. Attach mud guard to fender with #10 screws and washers at locations A and D. F-150 with flares F-150 without flares and with factory running board 5659_5656 Front Instr#1170E. doc Rev: 1 PART NO. PAINTING INSTRUCTIONS 1. Clean mud guard with a soap and water solution to remove dirt and other contaminates. Sand painting surface with 320 grit sand paper. Apply a coating of flexible primer-adhesion promoter. Apply a flexible paint as directed by the paint manufacturer. PAINT PROTECTION FILM - INSTALLATION INSTRUCTIONS 5659 / 5656 NOTE: The Paint Protection Film is a precut template of film used to protect the mud guard mounting surfaces of your fenders against wear. The templates (left and right side) can be removed from the backing liner by folding the liner at the center cut of the template, separating the film sides and peeling the film templates from the backing liner. Due to the rock guard on F-150 pickups without fender flares some trimming of the film template will be required for part no. Simply place film against fender in the mud guard contact area, place mud guard over film and mark where film needs to be trimmed away from plastic rock guard. Position mud guard on fender to indicate placement location of paint protection film. [. . . ] Check location of film with mud guard and reposition as necessary. Using a sponge, squeegee any air bubbles and wrinkles from film. Allow film to dry before installing mud guard. 5659_5656 Front Instr#1170E. doc Rev: 1 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSKY LINERS 5659

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSKY LINERS 5659 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag