User manual HUSQVARNA 1200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUSQVARNA 1200. We hope that this HUSQVARNA 1200 user guide will be useful to you.

Lastmanuals help download the user guide HUSQVARNA 1200.


HUSQVARNA 1200 : Download the complete user guide (1171 Ko)

Manual abstract: user guide HUSQVARNA 1200

Detailed instructions for use are in the User's Guide.

[. . . ] They assume a thorough knowledge of the handling of precision appliances and accessibility to service tools. The manual is divided into four sections and covers all service operations and checks which should be carried out when making a complete overhaul of a sewing machine. The second section deals with the various settings which must be maintained to ensure that the machine functions satisfactorily. The diagrams only give indication as to where the detail or mechanism is located in the machine. [. . . ] When tightening the screws on the pulley, the pointed screw should change places with the black screw that was unsrewed earlier. Mount the hook cover, the rear cover, the lamp cover and the handwheel. Comments By moving the needle all the time by means of the short cog belt, this will counteract any possible play between the long cog belt and the cog wheels. The axial play of the arm shaft might change when loosening the screws. 30 Husqvarna service manual 104 72 30-26 SEWKNITWORLD 10 The needle height Requirements Set the machine for zig-zag, right-hand position, Setting 6 mm stitch width. Move the needle upward by pulling the short cog position belt in toward the machine and at the same time holding the hook downward, backward. When the tip of the hook reaches the centre line of the needle, the underneath of the tip should be in line with the top edge of the needle eye. 5mm) is the starting measurement but as this is difficult to estimate, use the corresponding measurement with the needle at the right-hand position instead. Move the needle upward by pulling the short cog belt in toward the machine until the tip of the hook reaches the centre line of the needle. Push the hook downward and hold it, so that the catch of the hook rests against the left side of the slot in the driver. Move the needle bar in such a way until the underneath of the tip of the hook is in line with the top edge of the needle eye. Check that the needle eye is at right angles to the hook by fitting a twin needle and observing the needle positions in the needle hole of the stitch plate. Right hand position SEWKNITWORLD 104 72 30-26 Husqvarna service manual 31 Thread tension 11 The thread tension of the bobbin case Requirements The thread tension spring of the bobbin case shall give a thread resistance of 18-22 g when pulling the tread slowly. Adjustment Remove any loose pieces of thread collected under the thread tension spring. Attach the thread to the weight and hold the bobbin case, letting the thread hang vertically in direction of the bobbin case finger. When the thread tension is correctly set the weight shall pull the thread slowly from the bobbin case. 12 Upper thread tension Requirements, model 1050/1070/1090 When the machine is set at straight stitching resp. Zig-zag, a correct take-up should be obtained, when the catch of the thread tension pulley (5, 5) is right in front of the index. Requirements, model 1100/1200 When the sewing guide of the machine is set at non elastic normal and straight stitching resp. Zig-zag, a correct take-up should be obtained, when the catch of the thread tension pulley (5, 5) is right in front of the index. Comment 1 The sewing guide adjusts the thread tension to the fabric resp. This is done by means of the computer and the step motor of the machine. [. . . ] Check by means of the service cassette that the arm shaft sensor is working. Check that the cable connection of the step motor to the circuit board is correct (P. Check the signals of the circuit board to the step motor by means of the diagnoster and replace the circuit board in case of error (P. Check by means of the service cassette that the arm shaft sensor is working. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 1200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 1200 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag