User manual HUSQVARNA 323 HE3

[. . . ] Operator’s manual (EPA) 325HDA55X-series 323HE3 325HE3X-series 325HE4X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. Always wear approved protective gloves. Regular cleaning is required. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Visual check. Always wear: • • Approved hearing protection Approved eye protection Protective goggles or a visor must be worn. Cutting tool. [. . . ] See instructions under the heading Gear housing. Check that the cutting attachment always stops when the engine is idling. Only use the machine for the purpose it was intended for. Make sure that the handle and safety features are in good working order. Never use a machine that lacks a part or has been modified outside its specifications. All covers must be correctly fitted and undamaged before you start the machine. Starting Hold the body of the machine on the ground using your left hand (CAUTION!Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Push the choke control back to its original position as soon as the engine fires, and continue trying to start until the engine starts. Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. • Starting and stopping ! WARNING!The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Always move the machine about 3 metres from the refuelling position before starting. Remember that the blades may start to move when the engine is started. Make sure the blades cannot come into contact with any object. Make sure that no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres. Stopping The engine is switched off by moving the stop switch to the stop position. Cold engine Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. The stop switch automatically returns to the start position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance. 14 – English WORKING TECHNIQUES General working instructions IMPORTANT!This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. [. . . ] Clean dirt, leaves and surplus lubricant, etc from the muffler and engine. Daily maintenance X X X X X X X X X X X X X X X X X X X X X X X X X Weekly maintenance Monthly maintenance 22 – English TECHNICAL DATA Technical data Technical data Engine Cylinder displacement, cu. in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer/type of carburetor Fuel tank capacity, US pint/litre Weight Weight without fuel, Lbs/kg Sound levels (see note 1) Equivalent sound pressure level at the user′s ear, measured according to ANSI B175. 3-1997, dB(A), min/ 92 max: Vibration levels Vibration levels at handles, measured according to ANSI B175. 3-1997, m/s2 Idle speed, rear/front handles: Max. speed, rear/front handles: Blades Length, mm Blade speed, cuts/min 550 4184 550 4184 550 4184 550 4184 3, 5/1, 8 3, 1/5, 7 3, 8/1, 4 4, 7/5, 5 3, 8/1, 4 4, 7/5, 5 2, 2/1, 8 7, 5/6, 6 93 93 91 12, 8/5, 8 12, 8/5, 8 13, 2/6, 0 13, 7/6, 2 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 WalbroMB/ SEM AM49 NGK BPMR 7A 0, 02/0, 5 WalbroMB/ SEM AM49 NGK BPMR 7A 0, 02/0, 5 WalbroMB/ SEM AM49 NGK BPMR 7A 0, 02/0, 5 WalbroMB/ SEM AM49 NGK BPMR 7A 0, 02/0, 5 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-12600 0, 9/9000 Yes Yes 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-12600 0, 9/9000 Yes Yes 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-12600 0, 9/9000 Yes Yes 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-12600 0, 9/9000 Yes Yes 325HDA55 323HE3 325HE3 325HE4 Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. [. . . ]