User manual HUSQVARNA 323 L

[. . . ] Operator's manual (EPA II) 322L 323L 325C 325CX-SERIES 325LX-SERIES 325LXT-SERIES 325LDX-SERIES Please read these instructions carefully and make sure you understand them before using the machine. English SYMBOL EXPLANATION Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. [. . . ] • 322L/323L: Fit the nut, washer and bolt. 325LX/325LXT/325LDX: Fit the nut, knob and bolt. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembly of the trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. ! 12 – English WARNING!Under no circumstances may the cutting equipment be used without an approved guard fitted. See the chapter “Technical data”. If the wrong guard or a defective guard is fitted this can cause serious personal injury. ASSEMBLY Assembling the spray guard and trimmer head Superauto II (322L, 323L, 325LX, 325LXT, 325LDX) • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. • The trimmer head must be split to be fitted (see the diagram). Proceed as follows: • Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. Press apart the trimmer head using the fingers on the cover. • Place the cover (I) and the support flange (F) on the output axle. The tightening torque of the nut is 35-50 Nm (3, 5-5 kpm). Hold the handle of the spanner as close to the trimmer guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). • Fit the trimmer head‘s bottom section (K) on the cover (I) by pressing the two sections together with the cut-outs on the bottom section aligned with the catches on the cover. • To dismantle follow the instructions in the reverse order. Assembling other guards and cutting equipment (322L, 323L, 325LX, 325LXT, 325LDX) • Fit the appropriate guard (A) for use with the trimmer head. [. . . ] 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 Attachments Clean sweep attachment with shaft Hedge trimmer attachment with shaft Edger with attachment shaft Saw attachment with shaft Saw attachment without shaft Art No. 537 19 67-01 537 19 66-01 537 19 69-01 537 18 33-17 537 18 33-12 Use with 325LDX 325LDX 325LDX 325LDX 322L, 323L, 325LX, 325LDX English – 23 EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. Husqvarna Forest & Garden must warrant the emission control system on your small nonroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. [. . . ]