User manual HUSQVARNA 532440469

[. . . ] 07002 YTH24V48LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 04-69 Rev. 1 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. [. . . ] IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Install and tighten blade bolt securely (45-55 Ft. Lbs). IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED. MANDREL ASSEMBLY BLADE BLADE BOLT (SPECIAL) STAR CENTER HOLE Fig. 16 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the Service and Adjustments section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 15 BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. 15 MAINTENANCE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. [. . . ] 960 43 01-29 MOWER DECK 52 33 17 24 57 19 47 16 34 25 32 45 43 5 23 46 16 43 55 27 50 3 42 33 41 35 36 37 15 38 16 8 39 61 62 42 60 49 40 22 4 65 14 51 24 21 6 48 54 18 53 31 30 20 59 44 1 9 58 2 29 28 14 10 13 7 11 48_F_elec-Tex_2_r2 48_F_elec-Tex_2 12 40 TRACTOR - MODEL NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 33 34 35 PART NO. 574 80 95-01 539 11 21-70 532 18 76-90 532 17 43-75 532 40 02-34 532 17 39-84 532 11 07-32 532 11 07-35 532 11 07-36 539 11 34-25 532 19 30-03 539 11 34-26 872 11 05-05 873 80 05-00 532 19 51-61 539 11 28-99 532 19 61-04 574 82 71-01 532 17 79-68 539 13 27-28 575 22 45-01 539 10 76-10 532 19 34-06 521 99 65-01 575 22 47-01 539 10 47-63 539 10 82-71 539 10 65-04 819 14 16-14 539 97 69-79 539 99 09-23 539 10 48-64 532 17 85-15 539 11 91-24 DESCRIPTION Deck w/ Decals 48" Housing Assembly Washer-Spacer Pulley, Mandrel Nut, 9/16 Top Lock Screw Thd. Roll Discharge Chute, 48" Spring - Torsion Pin, Clevis 5/16 x 5. 19 Blade, 16-1/4" Bolt, 7/16, Assy Blade Confinement Plate Rhsnb 5/16-18 x 5/8 Nut 5/16-18 Stud, Fasten w/ Anti- Rotate Nut 5/16-18 Hex Flange Nyloc Pulley, Idler Spec. [. . . ]