User manual HUSQVARNA 96043001100

[. . . ] 03002 GTH26K54T Owner's Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers DANDER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. [. . . ] Some adjustments will need to be made periodically to properly maintain your tractor. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ STEERING SECTOR GEAR TETH ➀ MANDREL ZERKS 02956 BEFORE EACH USE • • • • • Check engine oil level. Check operator presence and ROS systems for proper operation. Check for loose fasteners. ➀ General Purpose Grease ➁ Refer to Maintenance “ENGINE” Section IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. 17 MAINTENANCE TRACTOR Always observe safety rules when performing any maintenance. BLADE CARE For best results mower blades must be sharp. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See PSI on tires). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. ROS "ON" Position Engine "ON" Position (Normal Operating) BLADE REMOVAL (See Fig. 23) Raise mower to highest position to allow access to blades. [. . . ] Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. Fold this page along dotted line indicated above. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. [. . . ]