User manual HUSQVARNA 96143000102

[. . . ] 5521CHV Owner’s Manual 532 19 90-33 04. 18. 05 BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Look for this symbol to point out important safety precautions. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. [. . . ] Wait until blade and all moving parts have stopped and turn fuel valve to OFF position if you do not intend to restart the engine soon. 9) NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. Be sure fuel valve is in the ON position. Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back. MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING” IN THE MAINTENANCE SECTION OF THIS MANUAL. • 8 The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. OPERATION • Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. MAX 1/3 • • • FIG. 10 Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. MAINTENANCE BEFORE EACH USE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel system or add Stabilizer AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE * (if so equipped) ** Electric-Start mowers *** Power-Propelled mowers **** Use a scraper deck to clean under 1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil. 5 - And after each 5 hours of use. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. [. . . ] Failure to do so could be hazardous, damage your lawn mower and void your warranty. ROTARY LAWN MOWER - - MODEL NUMBER 5521CHV (96143000102) - PRODUCT NUMBER 961 43 00-01 18 ROTARY LAWN MOWER - - MODEL NUMBER 5521CHV (96143000102) - PRODUCT NUMBER 961 43 00-01 KEY NO. 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 18 25 26 28 32 35 36 38 40 PART NO. 532 19 34-80 532 19 10-39 532 17 52-62 532 18 56-81 532 19 41-49 532 19 90-93 532 75 11-52 532 18 06-26 532 14 52-12 532 18 07-67 812 00 00-58 532 75 00-03 532 18 94-03 532 19 10-17 532 06 77-25 532 18 55-74 532 19 90-89 532 15 00-78 532 18 55-79 532 19 40-18 532 19 51-10 DESCRIPTION KEY NO. 41 54 55 57 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 PART NO. DESCRIPTION Drive Control Assembly, with Cable Bearing, Wheel Adjuster Pan Head Tapping Screw #10-24 x 2-3/4 Hex Washer Head Screw 1/4-20 x 2. 12 V-Belt Control Bar, Drive Locknut, Hex #10-24 Hubcap Locknut, Hex Wheel & Tire Assembly E-Ring Pinion Dust Cover Pawl, Drive Washer 1/2 x 1-1/2 x . 134 Selector Knob Belt Keeper Screw Drive Cover Drive Pulley Kit, Wheel Adjuster, LH (Includes Knob and Bearing) 532 18 82-96 Gearcase Assembly, Complete 873 80 04-00 Locknut, Hex 1/4-20 532 19 28-49 Spring 532 19 51-07 Kit, Wheel Adjuster, RH (Includes Knob and Bearing) 532 19 47-24 Grassbag Assembly 532 17 57-39 Driveshaft Cover 532 19 46-43 Frame, Grassbag 532 18 90-66 Decal, Drive Cover 532 19 68-86 Case, Upper 532 19 68-85 Shaft, Output 532 18 35-08 Seal, Output Shaft 532 18 35-11 Bushing 532 18 35-09 Washer 532 18 35-14 Seal, Worm Shaft 532 18 35-06 Bearing, Ball 532 18 34-99 Gear, 27 Teeth 532 19 68-84 Fixed Dog Clutch 532 18 35-05 Wireform 532 19 68-83 Movable Dog Clutch 532 19 68-82 Fork 532 18 35-13 Screw, Case 532 19 68-81 Case, Lower 532 19 68-80 Seal, Lever 532 19 68-79 Lever 532 19 68-78 Screw, Lever 532 19 68-77 Spring 532 18 35-02 Shaft, Worm 19 NOTE: All component dimensions given in U. S. [. . . ]