User manual HUSQVARNA 966503701

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUSQVARNA 966503701. We hope that this HUSQVARNA 966503701 user guide will be useful to you.

Lastmanuals help download the user guide HUSQVARNA 966503701.


Mode d'emploi HUSQVARNA 966503701
Download
Manual abstract: user guide HUSQVARNA 966503701

Detailed instructions for use are in the User's Guide.

[. . . ] Operator Manual RZ3016 CA / 966503701 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. In order to implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. [. . . ] Damage to engine and components may occur. IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur. Fuel tank 8050-012 WARNING!The engine and the exhaust system, become very hot during operation. Allow engine and exhaust system to cool at least two (2) minutes or a safe temperature before refueling. WARNING!Do not store, spill or use gasoline near an open flame. 20 CONTROLS Fuel Shut Off Valve The fuel shut off valve is located in the fuel line under the seat. The fuel valve is ON when the valve is parallel to the fuel line. Rotate the valve ¼ turn clockwise to turn fuel OFF. IMPORTANT INFORMATION In order to obtain an even cutting height, it is important that the air pressure is 15 psi in all tires. 8050-010 Fuel shut off valve in the OPEN position. Mower Deck Lifting Lever The lifting lever is used to place the mower deck in the transport position or one of the 6 different cutting height positions. The cutting height is set by placing a lever in the notch for the desired cutting height. The lifting lever can also be used to temporarily adjust the cutting height, such as when passing a minor bump in the lawn. IMPORTANT INFORMATION Always use the high position (F) to transport. 8058-085 The mower deck’s lifting lever Tracking If the mower is not tracking straight, check the air pressure in both rear tires. (1 bar) Tracking must be checked on a flat and level concrete or blacktop surface. If the unit still does not track straight contact your Husqvarna workshop for adjustments. 21 CONTROLS Blade Control Lever To engage the mower blades, slowly lift the lever up and into the the lock notch. WARNING!No adjustments or maintenance to be carried out unless: • • • the engine stopped the ignition key removed the parking brake activated 8058-074 Mower deck blade control lever in the disengaged position Manual Transport When pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard. • Raise the deck into the highest cutting position. • Pull the EZT bypass linkages out and into the slots. Release linkages to hold in the bypass position. • To reengage the EZT’s to drive, reverse the above procedure. 8050-018 Set bypass linkages into slots on both sides 22 operation Read the Safety section and following pages, if you are unfamiliar with the machine. Steering To move forward and backward The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. [. . . ] The safety switch in the steering controls. Check the idle speed Check the engine high idle speed Inform the customer about: The need and advantages of following the service schedule. The need and advantages of leaving the machine for service every 300 hours. The effects of service and maintaining a service journal on the machine’s resale value. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 966503701

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 966503701 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag