User manual HUSQVARNA 967916018

[. . . ] Never allow adults to operate the equipment without proper instruction. Keep the area of operation clear of all persons, particularly small children, and pets. Thoroughly inspect the area where the equipment is to be used and remove all foreign objects. Disengage all clutches and shift into neutral before starting the engine (motor). [. . . ] 15 TINE SHEAR PINS The tine assemblies on your tiller are secured to the tine shaft with shear pins (See “TINE REPLACEMENT” in the Service and Adjustments section of this manual). If the tiller is unusually overloaded or jammed, the shear pins are designed to break before internal damage occurs to the transmission. • If shear pin(s) break, replace only with those shown in the Repair Parts section of this manual. • 10 MAINTENANCE US RS RS OU 0H Y5 ER YS EA S MAINTENANCE SCHEDULE EA RE E UR OU CH HO FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Engine Oil Level Change Engine Oil Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge Clean Engine Cylinder Fins Replace Spark Plug RH Gear Case Grease Fitting (1oz. ) Y5 FO ER ER Y2 ER 5H SO N BE EV EV 1, 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. EV EV SERVICE DATES GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year you should replace the spark plug, clean or replace air filter, and check tines and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART THROTTLE CONTROL ENGINE RH GEAR CASE GREASE FITTIG DEPTH STAKE PIN BEFORE EACH USE • • • Check engine oil level. Check for loose fasteners. IDLER BRACKET WHEEL HUB LEVELING SHIELD HINGES LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”). SAE 30 OR 10W-30 MOTOR OIL REFER TO MAINTENANCE “ENGINE” SECTION EP #1 GREASE 11 MAINTENANCE Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Keep the engine free of grass, leaves, spilled oil, or fuel. Service air cleaner more often under dusty conditions. TO SERVICE PRE-CLEANER • Remove foam pre-cleaner from air cleaner cover. • Wash it in liquid detergent and water. • If very dirty or damaged, replace pre-cleaner. • Reinstall pre-cleaner into air cleaner cover. • Reinstall cover and secure screw. TO SERVICE CARTRIDGE • Carefully remove cartridge to prevent debris from entering carburetor. Clean base carefully to prevent debris from entering carburetor. • Clean cartridge by tapping gently on flat surface. If very dirty or damaged, replace cartridge. • Reinstall cartridge, cover with pre-cleaner and secure with screw. IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. [. . . ] 5 532 12 47-17 Cap, Vinyl 532 10 92-27 Pad, Idler 532 12 50-16 Shield, Leveling 532 12 05-88 Pin, Hinge 532 14 22-93 Shield, Side 873 97 05-00 Locknut, Flange 5/16-18 873 22 04-00 Nut Fin Hex 1/4-20 UNC 810 04 04-00 Washer Lock Hvy Helical 1/4 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 24 REPAIR PARTS TILLER - - MODEL NUMBER 650CRT (650RTTB), PRODUCT NUMBER 954 32 91-72 TINE ASSEMBLY 2 1 1 1 3 5 1 4 3 11 11 2 9 8 6 7 9 9 10 4 9 tine_ipb_1 KEY NO. 532 00 44-59 532 13 26-73 532 00 65-54 532 12 46-60 532 13 27-27 873 61 06-00 810 04 06-00 DESCRIPTION Tine, Outer, L. H. Retainer, Spring Zinc Assembly, Hub and Plate, L. H. [. . . ]