User manual HUSQVARNA FRONTKEHRMASCHINE

[. . . ] 11 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Assembly/Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 . [. . . ] Never allow persons not trained in the use of the machine to perform service on it. Always park the machine on even ground before performing maintenance or making adjustments. This can invalidate your engine warranty. Contact your dealer if you have any questions regarding service or guarantee matters. Do not change the setting of governors and avoid running the engine with overly high RPM. If you run the engine too fast, you risk damaging the machine components. Check regularly to be sure it works properly. The machine must not be run with defective or disassembled safety equipment. The muffler is designed to maintain sound levels at an approved level and keep direct exhaust away from the user. Exhaust gases from the engine are extremely hot and may contain sparks that can cause fires or burn the user. Never use a machine with a defective muffler. Drain the fuel tank and replace with fresh fuel. If this does not help, contact an authorized service workshop. Do not fill the tank completely; leave space for the fuel to expand as it warms up. 8011-019-1 WARNING!Observe caution and fill the tank outdoors. (See the safety instructions. ) Cutting Unit Depth Lever Use the depth lever to raise and lower the blades between working and transport position. The depth lever has a lock-out bolt that should be left in until the blades wear down. Then move the bolt to a lower hole to allow the blades to penetrate the soil. • Flail Blades or Spring Tines Set blade or tine depth so that the blades or tines just touch on a flat surface such as a sidewalk or driveway. • Delta Blades Set blades to penetrate the soil to a depth of 1/8" to ¼" with a maximum penetration of ½". Check seed bag for the manufacture’s recommended depth of application • Lawns with deep thatch exceeding ¾" may be best dethatched in two treatments (spring and fall) to avoid major shock to an older lawn. Clutch The clutch tightens the drive belt and engages the drive for the blades. When the clutch lever is pressed against the handle, the blades begin to rotate. [. . . ] 6. Remove the spark plug and pour about a tablespoon of engine oil in the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug. 7. Lubricate all grease nipples, joints and shafts as described in the chapter “Lubrication/Lubrication Schedule”. 8. Store the machine in a clean, dry place and cover for extra protection. Service When ordering spare parts, please specify the p ­ urchase year, model, type, and serial number. [. . . ]