User manual HUSQVARNA HECTH155C

[. . . ] Always use • A protective helmet where there is a risk of falling objects • Ear protection • Approved eye protection Other symbols/decals on the machine refer to special certification requirements for certain markets. max 10000 rpm • Max. speed of output axle, rpm • This product is in accordance with applicable CE directives. Checks and/or maintenance should be carried out with the engine switched off, with the stop switch in the STOP position. • Beware of thrown objects and ricochets. Always wear approved protective gloves. • Warning for rotating blade. Regular cleaning required. • Warning!The blade continues to rotate even after the engine has stopped. Ocular control. When the engine has stopped, stop the blade from rotating by letting the blade come in contact with the ground. [. . . ] • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children. • Only use original spare parts with repair. English – 11 WHAT IS WHAT? 1 4 21 4 20 1 26 24 What is what on the edger? 1. Blade Grease filler cap Angle gear Blade guard Shaft Loop handlebar Throttle Stop switch Throttle trigger lock 15. Air purge 12 – English ASSEMBLY Assembling the loop handlebar • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Assembling the blade Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fits in the hole of the blade is facing outward. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in the corresponding hole in the drive disc. • When working at continuous high revs a higher octane rating is recommended. !The catalytic converter muffler gets very hot during and after use. Be aware of the fire hazard, especially when handling the saw near flammable substances or vapours. Fuelling WARNING!The following precautions reduce the risk of fire: Do not smoke or place any sources of heat in the vicinity of the fuel. Never refuel when the engine is running. Always stop the engine and let it cool for a few minutes before refuelling. Open the fuel cap slowly when fuelling so that any over pressure is released slowly. Tighten the fuel cap carefully after refuelling. Always move the machine from the fuelling place before starting. Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for two-stroke engines. • Never use two-stroke oil intended for water cooled outboard motors, so-called outboard motor oil. • Never use oil intended of four-stroke engines. • Clean around the fuel cap. [. . . ] speed, rpm Idling speed, rpm Speed of output axle, rpm Max. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system 1, 33/21, 7 1, 26/32 1, 06/27 11 000 - 11 700 2 700 8 300 0, 7 kW/9. 000 rpm Yes Yes Walbro MB 21 Champion RCJ 7Y 0. 02/0, 5 Zama C1Q 1, 06/0, 5 11, 0/ 5, 0 1, 50/24, 5 1, 34/34 1, 06/27 11 000 - 11 700 2 700 8 300 0, 9 kW/9. 000 rpm Yes Yes Walbro MB 21 Champion RCJ 7Y 0. 02/0, 5 Zama C1Q 1, 06/0, 5 11, 2/5, 1 322E 325E-X Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel lubrication system Manufacturer/type of carburetor Fuel tank capacity, US pint/litres Weight Weight without fuel and cutting tool, Lbs/kg Noise levels Equivalent noise pressure levels at the user‘s ear, measured according to prEN 31806 and ISO 7917, dB(A). Blade: Equivalent noise power levels measured according to prEN 31806 and ISO 10884, dB(A). Blade: 96 96 102 102 Vibration levels Vibration levels on the handles measured according to prEN 31806 and ISO 7916, m/s2 Blade, idling rear/front handles: Blade max. [. . . ]