User manual HUSQVARNA HNS1136B

[. . . ] Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • • • A protective helmet where there is a risk of falling objects Approved hearing protection Approved eye protection Regular cleaning is required. Only use non-metallic, flexible cutting attachments, i. e. trimmer heads with trimmer cord. Other symbols/decals on the machine refer to special certification requirements for certain markets. [. . . ] Use low-emission gasoline, also known as alkylate gasoline, if it is available. Transport and storage • Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/ switches or boilers. When storing and transporting fuel always use approved containers intended for this purpose. When storing the machine for long periods the fuel tank must be emptied. Contact your local gas station to find out where to dispose of excess fuel. Ensure the machine is cleaned and that a complete service is carried out before long-term storage. The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. • • This engine is certified to operate on unleaded gasoline. • The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage. When working at continuous high revs a higher octane rating is recommended. • • ! Fuel WARNING!Bear in mind the risk of fire, explosion and inhaling fumes. • Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found. ! WARNING!The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Always move the machine away from the refuelling area before starting. Ensure the cutting attachment cannot come into contact with any object. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres. • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. Cold engine Ignition: Set the stop switch to the start position. Choke: Set the choke control (A) in the choke position. Primer bulb: Press the air purge diaphragm (B) repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. • Ensure the locking nut has not lost its captive force. [. . . ] speed, left/right handles, min. : At max. speed, left/right handles, max. : 2, 1/2, 4 3, 4/4, 2 2, 0/2, 1 2, 8/3, 3 97/100 18, 1/8, 2 Zama C1Q 1, 9/0, 9 SEM AM Champion RCJ 6Y 0, 02/0, 5 2, 75/45 1, 65/42 1, 26/32 2800 12500 9000 2, 0/9000 No Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idling and 1/2 max speed. Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 38 – English TECHNICAL DATA 343R, 345RX Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S Trimmer head Trimmy S II Auto 55 T45x Support cup Fixed With ball bearing 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. [. . . ]