User manual HUSQVARNA HU 5524 ST A

[. . . ] 5524ST Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adLook for this symbol to point out imequate winter outer garments. Avoid loose, dangling portant safety precautions. [. . . ] To avoid possible freeze-up of the starter, proceed as follows: 1. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps. SNOW THROWING TIPS • • • • Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance. Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed. It is easier and more efficient to remove snow immediately after it falls. The best time to remove snow is the early morning. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. Keep engine clean and clear of snow during use. This will help air flow and extend engine life. After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use. WARNING: Do not operate snow thrower if weather conditions impair visibility. [. . . ] 8, 12, 13 & 45) 13 532 08 51-79 Retainer, Hairpin 14 532 17 88-28 Spring, Brake 15 532 18 35-33 V-Belt, Impeller Drive 16 532 15 04-06 Screw, Hex Head 3/8-16 x 1-1/4 17 532 18 48-04 Arm, Idler 18 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2 19 532 17 53-31 Bushing, Idler Pivot 20 532 18 05-23 Pulley, Idler (2-3/4) 21 874 61 05-16 Screw, Hex Head 5/16-18 x 1 22 532 17 93-71 Spacer, Engine Pulley 23 532 18 04-78 Pulley, Engine, Traction Drive 24 532 17 91-57 Pulley, Engine, Impeller Drive 25 532 06 27-35 Washer, Flat 3/8 26 810 04 06-00 Washer, Lock 3/8 27 532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8 28 532 15 54-52 Guide, Belt 29 532 18 04-65 Cover, Belt 30 532 17 88-30 Cover, Toolbox 31 817 49 04-08 Screw, Hex Head 1/4-20 x 1/2 32 532 17 92-56 Bolt, Shoulder 5/16-18 33 532 17 92-50 Bellcrank Shifter 34 532 18 04-01 Screw, Hex Head 1/4-28 x 3/4 35 532 17 92-40 Arm, Auger Control 36 873 80 05-00 Nut, Lock 5/16-18 37 532 18 40-86 Bellcrank Assembly 38 532 17 92-51 Link, Speed Control 39 532 17 90-64 Trunnion, Pivot Bracket 40 532 17 88-90 Nut, Cage 3/8-16 41 876 02 02-08 Pin, Cotter 1/16 x 1/2 42 532 17 90-65 Pin, Pivot Bracket 43 532 18 40-85 Bracket, Bellcrank 44 874 78 06-24 Screw, Hex Head 3/8-16 x 1-1/2 45 532 18 47-89 Arm & Bracket Assembly, Impeller Idler (Includes Key Nos. 8, 12, 13 & 45) 46 532 18 40-84 Pan, Frame Bottom 47 871 02 05-12 Screw, Hex Head 5/16-18 x 3/4 48 532 18 11-56 Nut, Speed 5/16-18 49 532 18 40-73 Frame Assembly 50 532 18 40-83 Plate, Frame End 51 532 18 40-82 Shaft, Auger Control 52 532 05 70-79 Washer, Hardened 53 532 17 90-62 Roller 54 812 00 00-10 Ring, Retaining 55 532 70 02-79 Clip, Retainer NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 29 1 2 3 REPAIR PARTS WHEELS / DECALS 2 SNOW THROWER - - MODEL NO. 954 22 30-67 1 4 5 6 4 1 3 2 5 3 1 10 2 4 9 8 6 5 1 10 3 30 10 7 REPAIR PARTS WHEELS / DECALS SNOW THROWER - - MODEL NO. [. . . ]