User manual HUSQVARNA INSTRUCTION SHEET FOR KIT 96071003200 CD TEX DEFLECTOR

[. . . ] Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. • • • • • • • • • WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. • • Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working. [. . . ] NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. ROS "ON" Position Engine "ON" Position (Normal Operating) BLADE REMOVAL (See Fig. 13) Raise mower to highest position to allow access to blades. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. • Remove blade bolt by turning counterclockwise. Be careful not to allow dirt to enter the engine when changing oil. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting. • Unlock drain valve by pushing inward and turning counterclockwise. OIL DRAIN VALVE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. CLOSED AND LOCKED POSITION 46 02 3 YELLOW CAP DRAIN TUBE TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. 15 • • • • To open, pull out on the drain valve. [. . . ] 960 43 00-05 KOHLER ENGINE - MODEL NUMBER SV600-0002 STARTING SYSTEM KEY NO. 1 2 CRANKSHAFT KEY NO. 1 2 3 PART NO. 2009806-s 2510031-s 1 2 DESCRIPTION Starter Assy, Inertia Drive Nut, Free Spinning Flg #10-24 PART NO. 2001420-s 2004312-s X-42-15-s 1 1 1 DESCRIPTION Kit, Crankshaft Gear, Crankshaft Key, 3/16” X 5/8” Oil Pan/lubrication EXHAUST DESCRIPTION 1 2 1 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. 2004002-s 2015301-s 2000903-s KEY NO. 1 PART NO. 2507204-s 2 1 1 1 1 1 DESCRIPTION Stud, M8x1. 25x33 Decal, Clear Decal, 20 Hp Decal, Wing Set 5v590/600 Short Block Gasket Set Kit, Dipstick Blade (Includes 2) O-ring Kit, plate, Closure Bearing (Includes 4, 10, 11) 2513960-s 2 Plug, CTSK Pipe 1/8” 5205002-s 1 Filter, Oil 20 041 01-s 1 Gasket, Closure Plate 2009602-s 1 Kit, Oil Passage Cover (Includes 8) 20 041 02-s 1 Gasket, Oil Passage 2014403-s 1 Shaft, Governor Cross 2031003-s 1 Kit, Governor Gear Assy (Includes 11) 1238001-s 1 Pin, Governor Regulating M-545013-s 6 Screw, Flg Thd Frm M5x0. 8x13 M-851030-s 14 Screw, Flg M8x1. 25x30 2003201-s 1 Seal, Oil 2515502-s 1 Connector, 90° Hose Not illustrated -2511339-s -2011336-s -2011337-s -20 522 01 -2075505-s FUEL SYSTEM KEY NO. 1 2 3 4 5 PART NO. 20 041 07-s 2033201-s 2026503-s M-651020-s 2085314-s 1 1 1 1 1 1 1 2 2 2 1 1 2 6 1 2 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION Gasket, Heat Deflector Insert, Intake Port Deflector, Heat Screw, Flg M6x1. 0x20 Kit, Carburetor W/gaskets (Includes 6, 7) Gasket, Air Cleaner Base Gasket, Carburetor Stud, M6x1. 0x100 Nut, Flg M6x1. 0 Screw, Flg Thd Frm M5x0. 8x10 Bracket, Fuel Pump Mounting Pump, Fuel Screw, Flg Thd Frm M6x1. 0x16 Clamp, Hose Filter, Fuel Line, Fuel (24”-cut To Length) Line, Fuel 10” Tie Washer, Int Tooth Lock 1/4” Sleeve, Fuel Line Kit, Choke Shaft Kit, Repair Float Kit, Repair Carburetor Kit, Repair Solenoid Kit, Repair Bowl Replacment Kit, High Altitude (5000 Ft) Kit, High Altitude (10, 000 Ft) ENGINE CONTROLS KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO. 2053605-s 2008610-s 1208911-s 1223701-s 2408643-s M-664020-s 1208911-s 2008610-s 2008911-s 2009002-s 52 211 04-s X-22-11-5 1210007-s 2515811-s 2007904-s 2515808-s 2008910-s 2007905-s 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 1 DESCRIPTION Kit, Speed Control Assembly (Includes 2, 3, 6-9) Screw, Phl Thd Frm M4x0. 7x25 Spring, Speed Control (Short) Clamp, Cable Screw, Lbd Thd Frm M5x0. 8x16 Screw, Lbd Skt M6x1. 0x20 Spring, Speed Control (Short) Screw, Phl Thd Frm M4x0. 7x25 Spring, Governor Lever, Governor Bolt, Rd Hd Sq Nck 1/4-20x1” Washer, Int Tooth Lock 1/4” Nut, Hex Flg 1/4-20” Bushing, Throttle Linkage Linkage, Throttle Bushing, Linkage Retaining Spring, Linkage Linkage, Choke Note: All Component Dimensions Given In U. s. Inches 1 Inch = 25. 4 Mm 6 12 041 02-s 7 12 041 01-s 8 2007205-s 9 M-641060-s 10 M-545010-s 11 2012602-s 12 2439316-s 13 M-645016-s 14 2523714-s 15 2505022-s 16 25 111 34-s 17 5235320-s Not Illustrated 2545405-s X-22-11-5 25 431 12-s 12755110-s 1275702-s 1275703-s 1275733-s 1275737-s 2075506-s 2075507-s NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 50 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA LON THIS G DO I TTED SA 15 D LINE EGR E E SL OPE 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. [. . . ]