User manual HUSQVARNA PA 1100

[. . . ] Re conta erlyi ently nt prop qu ceme r is g fre pla ine ba d re nta eck de s co Ch mmen n. les r unrioratio reco a INGmowe tie only RNerate and de e Us WA t op wear ged. no Do ct to dama or subjeed ck cra OWNER'S MANUAL Model No. PA 1100 42 Inch Mower Grass Catcher · · · · · Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 1 156235 Rev. [. . . ] If your drawbar looks like STYLE "B" (does not have the upper corner ribs), go to the PREPARATION section in this manual. UPPER CORNER RIBS TRACTOR DRAWBAR STYLE "A" TRACTOR DRAWBAR STYLE "B" PARTS IDENTIFICATION UPPER CHUTE COVER er tain on en d. C wh alle placetainer. en qu em is pro fre lac g rep er taineck ba ed nd s con Ch me les n. om r un ioratio rec we ly a NINGmod detier on e te era an Us t WARop wear ged. no Do ject to dama or sub d cke cra is DUMP BAG INDICATOR CHUTE LATCH er tain on en d. C wh alle placetainer. en qu em is pro fre lac g rep er taineck ba ed nd s con Ch me les n. om r un ioratio rec we ly a NINGmod detier on e te era an Us t WARop wear ged. no Do ject to dama or sub d cke cra is er tain on en d. C wh alle placetainer. en qu em is pro fre lac g rep er taineck ba ed nd s con Ch me les n. om r un ioratio rec we ly a NINGmod detier on e te era an Us t WARop wear ged. no Do ject to dama d or sub cke cra is LOWER CHUTE GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING STRAPS NOTE: When right hand (R. H. ) and left hand (L. H. ) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. (1) 3/8" Wrench (1) 1/2" Wrench (2) 9/16" Wrenches (1) 1/2" Socket (1) Drive Ratchet (1) 3" or longer Extension (1) Short Handle Phillips Screwdriver THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER: CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: · Depress clutch/brake pedal fully and set parking brake. 3) Use Hardware - - GROUP "B" CAUTION: Container support is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. END CAP 1. Rotate cover assembly onto its side as shown. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. CARRIAGE BOLTS LOCKNUTS SHORT HEX BOLT LONG HEX BOLT SUPPORT TUBE SUPPORT POST LOCKNUTS MOUNTING BRACKET LANCED TABS SUPPORT POST FIG. 4 ASSEMBLY 5 CONTAINER ASSEMBLY (See Fig. Place bottom half inside of top half, as shown. Place one foot inside bottom half and lift top half to meet bottom half. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 1. Install one container to left side first with warning to outside of unit. Install another container center position and one in right position. [. . . ] · Make sure the blade and all moving parts have completely stopped. · Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. NOTE ON SOME MODEL TRACTORS, MINOR MODIFICATIONS MAY BE NECESSARY TO MOUNT YOUR NEW GRASS CATCHER. NOT ALL MODEL TRACTORS WILL NEED THE FOLLOWING MODIFICATIONS. CHECK EACH STEP CAREFULLY TO DETERMINE IF MODIFICATION IS REQUIRED. [. . . ]