User manual HUSQVARNA YTH24V54XLS

[. . . ] 07002 YTH24V54XLS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 17-61 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] 5 - See Cleaning in Maintenance Section. GENERAL RECOMMENDATIONS The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART ➀ SPINDLE ZERK ➀ FRONT ➀ SPINDLE ZERK ➀ FRONT WHEEL BEARING ZERK WHEEL BEARING ZERK ➀ STEERING SECTOR GEAR TEETH ➁ ENGINE ➀ MANDREL ZERKS BEFORE EACH USE • • • • • Check engine oil level. Check operator presence and ROS systems for proper operation. Check for loose fasteners. 02501 ➀ ➁ General Purpose Grease Refer to Maintenance “ENGINE” Section 17 IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. MAINTENANCE TRACTOR Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See the sides of tires for proper PSI). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 28) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. [. . . ] RH Bearing, Race Thrust Harden Washer 25/32 x 1-5/8 x 16 Ga. Ring, Clip #T5304-75 Cap, Spindle Washer 25/32 x 1-1/4 x 16 Ga. Washer, Lock Hvy Hlcl Spr 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Adapter, Wheel Steering Steering Support Lower Insert, Wheel Steering Screw 3/8-16 x 3/4 Gear, Sector Plate Washer 9/16 x 2-3/8 x 12 Ga. KEY PART NO. 51 53 57 58 59 60 61 62 63 64 66 67 68 69 70 873 94 08-00 532 18 89-67 532 19 72-46 532 19 47-47 532 19 47-48 873 97 10-00 532 19 47-40 532 19 47-41 817 00 05-12 532 19 98-49 871 02 07-48 532 19 47-37 873 90 07-00 532 19 91-62 532 19 61-97 DESCRIPTION Nut Hex Jam Toplock 1/2-20 unf Washer Hardened . 793 x 1. 637 x . 060 Bracket Upstop Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/8-11 Draglink, LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. [. . . ]