User manual HUSTLER 102780

[. . . ] TrimStar Geardrive Owner's Manual ······· Hustler Turf Equipment ····· P. O. Box 7000 ··· Hesston, Kansas · 67062-2097 102780 6/05 WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 102780 6/05 TABLE OF CONTENTS 1. General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sect. Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sect. [. . . ] The engine should continue to run without the operator presence control switches engaged. If the engine fails to stop when the blade engagement lever is in the engaged (forward) position or the transmission shift lever either in the forward or reverse position and both operator presence control levers are released, check the function of the operator presence control switch. If this switch is not operating properly (not opening or closing) contact your Authorized Hustler Dealer. WARNING: The safety interlock system should always function per steps 3 and 4. If it does not function properly, it should be corrected immediately. Do not operate machine without properly functioning operator presence control switches. machine only. NOTE: The operator must disengage clutch before shifting gears. Deck cutting height adjustment Deck height is adjustable from 1-1/2" to 4-1/2" (3. 81 cm - 11. 43 cm) in 1/4" increments. Rear deck mount in the highest position (5) spacers on top of caster arm = 1 7/8" to 3 1/8" (4) spacers on top of caster arm = 2 1/8" to 3 3/8" (3) spacers on top of caster arm = 2 1/2" to 3 3/4" (2) spacers on top of caster arm = 2 5/8" to 3 7/8" (1) spacer on top of caster arm = 2 7/8" to 4 1/8" All spacers under caster arm = 3 1/4" to 4 1/2" Rear deck mount in the lowest position (5) spacers on top of caster arm = 1 1/2" to 2 3/4" (4) spacers on top of caster arm = 1 3/4" to 3" (3) spacers on top of caster arm = 2" to 3 1/4" (2) spacers on top of caster arm = 2 3/8" to 3 3/8" (1) spacer on top of caster arm = 2 5/8" to 3 7/8" All spacers under caster arm = 2 7/8" to 4 1/8" NOTE: Use 1/4" blade spacers to achieve cutting height between the above measurements. NOTE: For better mowing results, adjust the mowing height so that the blades are level front to back or slightly higher in the back. Moving unit with stalled engine If it becomes necessary to move the unit when the engine is inoperative, place the transmission shift lever in the neutral position. Move it by hand or use a winch to load on a trailer for transporting. When transporting on another vehicle, the unit must be tied down to the transporting vehicle. Mower deck operation DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly. With the engine running at 1/3 - 1/2 throttle, engage the blade engagement lever (Fig. 3-4) and advance engine throttle to full rpm. NOTE: Engaging the blades at high engine rpm or when under heavy load (in tall grass for example) can cause belts to slip, resulting in premature wear or possible damage. Steering the unit DANGER: Never make sudden stops or reverse direction, especially when operating on a slope. The steering is designed for sensitive response. After starting engine, shift the transmission to the desired gear (1 thru 4) for mowing, 5th gear is for transporting only, move thumb latches to the engaged position and steer as follows: To go forward, squeeze the drive levers and push forward on the thumb latches to unlock the levers. Slowly release drive levers to engage the drive wheels. To turn left, squeeze the left drive lever. To turn right, squeeze the right drive lever. To go in reverse, shift the transmission to the reverse position. [. . . ] These deposits will cause engine flooding and loss of power. 102780 6/05 6-1 PRODUCT LITERATURE This section contains sources of additional literature concerning your tractor. Literature should be ordered from your Hustler dealer, or direct from indicated source. NOTE: For parts information on your unit, refer to the TrimStar Parts Manual (Hustler P/N 102939). Engine information The TrimStar uses a Kawasaki 13hp, 15hp or 17hp engine. Primary source of information is the engine operator's manual, which is included with the TrimStar owner's manual packet. [. . . ]