User manual HYUNDAI HL760-7A BROCHURE

[. . . ] (Option) Full automatic shift lever A single lever on the left side of the steering column gives the operator fast and easy control of speed and direction. Push the lever forward to drive forward, pull it back for reverse. Travelling is automatically changed from 1st stage to given stage according to travel speed and traction effort. The operator can select two kinds of automatic modes (1st<->4th, 2nd<->4th). [. . . ] It comes with an anti-vandalism lock for machine protection. Centralised electric controllers & Fuse Box The electric controllers for this loader are centralized together with the fuse box to improve serviceability and facilitate inspections. Cabin Air Fresh Filter The internal pressure is maintained slightly higher than that of outside to exclude dust from and reduce noise level in the cabin. Coolant Sight Gauge A sight gauge is installed on top of the radiator tank for convenient checks of the coolant level. Easy Access to All Engine Components Here you find engine oil check and main and pre-filters. The large access engine-side-panels permit easy and safe inspections. The fuel and oil filters can be spun on and off for quick replacements. Up-to-date hydraulic remote cooling fan Minimum fuel consumption and low noise is realized by using a hydraulic cooling fan sensing coolant temperature, intake air temperature, transmission oil temperature and hydraulic oil temperature. Reversible cooling fan is installed. 9 HL760-7A_new_en 05-11-2007 13:33 Pagina 10 Specification Engine Maker/Model Type CUMMINS QSB6. 7 4-cycle, turbocharged, charge air-cooled direct injection, electronic controlled diesel engine Bore x Stroke Displacement Compression ratio Air cleaner Gross power Net power Maximum power Maximum torque No. of cylinders 160 kW (215 HP) at 2, 100 rpm 153 kW (205 HP) at 2, 100 rpm 162 kW (217 HP) at 1, 900 rpm 970 Nm (700 lbf. ft) at 1, 500 rpm 6 Alternator Battery Starting motor 107 mm (4. 2") x 124 mm (4. 9") 6. 7 litres (409 cu in) 17. 2 : 1 Dry, dual elements 24V, 70 Amp 2 x 12V, 130 Ah. 24V, 3. 7 kW Net power output of standard engine as installed in this vehicle (per SAE J1349) complete with fan, air cleaner, alternator, water pump, lubricating oil pump and fuel pump. No de-rating for continuous operating required up to 3658 m (12000 ft). This engine meets the EPA(Tier III) / EU(Stage III-A) Emission regulation. Transmission Torque converter type Stall torque ratio 3-elements, single-stage single-phase 2. 813 :1 Travel speed Forward km/h (mph) 6. 2 (3. 9) 11. 7 (7. 3) 22. 3 (13. 9) 34. 3 (21. 3) Reverse 6. 6 (4. 1) 12. 3 (7. 6) 23. 3 (14. 5) Full automatic power shift, countershaft type with soft-shift in range and direction. Properly matched torque converter to engine and transmission for excellent working ability. Axles Drive system Mount Rear axle oscillation Four-wheel drive system Rigid front axle and oscillating rear axle +/- 12° (total 24°) Hub reduction Differential Reduction ratio Planetary reduction at wheel end Differential, limited slip (front/rear) 24. 685 Hydraulic System Type Open-centred, tandem circuit system. Helical gear type, 280 litres/min (74 gal/min)@governed rpm Two function valve with single or two lever controls: Optional third-function valve with auxiliary lever. Tilt Circuit Relief Valve Setting Pilot System Type 20, 5 MPa (2, 990 psi) Pilot oil pressure is generated by the pilot oil supply unit. Cylinder Relief Valve Setting 2, 9 MPa (427 psi) Type: Double acting No. of cylinders-bore x stroke; Lift 2-160 mm (6. 3") x 757 mm (29. 8") Tilt 1-180 mm (7. 1") x 530 mm (20. 9") Raise: 6. 2 sec (with load) Dump: 1. 3 sec Lower: 3. 0 sec (empty) Total: 10. 5 sec Bucket Controls Type Pilot operated lift and tilt circuit, singlelever (joystick) control standard. The valve has four functions: raise, hold, lower and float. An adjustment for automatic kick-out from horizontal to full lift is installed. The valve has three functions: tilt back, hold and dump. An adjustment for automatic bucket position to the desired load angle is installed. Pump Control Valve Lift Circuit Cycle Time 10 HL760-7A_new_en 05-11-2007 13:33 Pagina 11 Specification Brakes Service Brakes Hydraulically actuated, wet disc brakes actuate all 4 wheels independent axleby-axle system. Single pedal braking including clutch cut off switch. Type Pump Steering System Full hydraulic power steering Helical gear type, 140 litres/min (37. 0 gal/min) 20, 5 MPa (2, 990 psi) Double acting 80 mm (3. 1") x 440 mm (17. 3") 40° (each direction) Relief Valve Setting Parking Brake Spring-applied, hydraulically released disc brake on front axle input shaft. When brake oil pressure drops, indicator light alerts operator and parking brake automatically applies. Cylinder Type Bore x Stroke Emergency Brake Steering Angle Features - Centre-point frame articulation. - Load-sensing, pressure-compensated system. [. . . ] transmission gear range indicator Optional Equipment 24-volt to 12-volt DC converter Air condition : . heater Beacon light, rotating Cutting edge, bolt-on type Fire extinguisher High lift arrangement with optional counterweight, 1630kg (3590 lb) Hour meter Hydraulic control, 2 lever Hydraulic control, 3 lever Hydraulic arrangement 3-valve Lighting, auxiliary, 4 on roof Mud guard Open Canopy (NONE-ROPS) Operator suit Seat . 2" static seat belt & adjustable mechanical suspension (vinyl) . 3" static seat belt & adjustable mechanical suspension . [. . . ]