User manual IBM THINKPAD 385D

[. . . ] i Note Before using this information and the product it supports, be sure to read the general information under "Notices" on page 213. First Edition (March 1997) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimers or express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. [. . . ] Installing Software 111 Installing IBM OS/2 Software Installing OS/2 Warp Using a Diskette Drive and CD-ROM Drive 1. Ensure that DOS and Windows are installed in the computer. Insert the OS/2 Warp CD-ROM into the CD-ROM drive. Open the DOS command prompt and change the current drive to the CD-ROM drive. Type CDINST and press Enter. Make copies of the OS/2 Warp diskettes according to the instructions on the screen and label the diskettes. 5. Shut down OS/2 and turn off the computer. Insert the OS/2 Warp Installation Diskette into the diskette drive and turn on the computer. When you are prompted to insert OS/2 Warp Diskette 1, insert it into the diskette drive and insert the OS/2 Warp CD-ROM into the CD-ROM drive. Note: If you have the OS/2 Warp FixPak 10 (XR0010) or later, install it after you complete the installation of OS/2. Follow the instructions in the README. 1ST file in diskette 1 of that FixPak. 8. Follow the instructions on the screen until the installation is complete. Pay attention to the following during installation: At the System Configuration screen, ensure that ThinkPad 755CD TEAC CD-40E is selected for the CD-ROM Drive. If not, select Non-Listed IDE CD-ROM or IDE CD-ROM for the CD-ROM drive. Remove any supported devices under Multimedia Device Support at the System Configuration screen. 9. Shut down OS/2 and restart the computer. 112 IBM ThinkPad 385 or 385D User's Guide Installing IBM OS/2 Software Installing the CD-ROM Device Driver for OS/2 If you installed a CD-ROM device driver (ThinkPad 755CD TEAC CD-40E or Non-listed IDE CD-ROM or IDE CD-ROM on the System Configuration screen) when installing OS/2, you do not need to install the CD-ROM device driver. Continue with "Installing the ThinkPad Features Program for OS/2. " If you have not installed a CD-ROM device driver when installing OS/2, have the diskettes that came with OS/2; then install the CD-ROM device driver for OS/2 as follows: 1. Open OS/2 System; then open System Setup. Select Install/Remove (for version 4. 0). Select Selective Install; then click on the CD-ROM Device Support. If ThinkPad 755CD TEAC CD-40E is present in the list, select this and click on OK. If not, select Non-Listed IDE CD-ROM or IDE CD-ROM and click on OK. Click on OK at the System Configuration screen. At the OS/2 Setup and Configuration screen, select Install; then follow the instructions on the screen. For information about the software parameter in the CONFIG. SYS file, refer to the README file in the CD-ROM Diskette. Installing the ThinkPad Features Program for OS/2 To install the ThinkPad Features program: 1. Start OS/2; then insert the Utility Diskette for OS/2 into the diskette drive. [. . . ] Often referred to as random-access memory (RAM), measured in kilobytes (KB) or megabytes (MB) of information. One or more microinstructions used in a product as an alternative to hard-wired circuitry to implement functions of a processor or other system component. A device that connects your computer to a telephone line, allowing it to communicate with another computer at another location. Moving Pictures Experts Group parallel port. [. . . ]