User manual ICOM BP-12G

[. . . ] · See the operatng gude for detals of BIIS (Bnary Interchange of Informaton and Sgnalng) and dPMR (dgtal Prvate Moble Rado) system operatons. Ask your dealer for detals. Icom, Icom Inc. and the Icom logo are regstered trademarks of Icom Incorporated (Japan) n Japan, the Unted States, the Unted Kngdom, Germany, France, Span, Russa and/or other countres. All other products or brands are regstered trademarks or trademarks of ther respectve holders. PRECAUTIONS RWARNING! [. . . ] 6 1 PANEL DESCRIPTION POWER OFF EMERGENCY Whle holdng down ths key, turn the power OFF to actvate the Power OFF Emergency functon. Ths functon makes the transcever transmt emergency calls, even though t appears to be powered OFF. 15) HOOK SCAN When the Hook Scan functon s pre-programmed, push ths key to dsable the functon. Push ths key agan to enable the functon. USER SET MODE Hold down for 1 second to enter the User Set mode. · In the User Set mode, push ths key to select an tem that s enabled by your dealer, and change the value or settng by pushng [CH Up] or [CH Down]. Hold down for 1 second agan to ext the User Set mode. The User Set mode s also avalable usng the Power ON functon. 10Key ENT Push to enable the mcrophone's 10-keypad operaton. · Dependng on the pre-programmed settngs, 10-keypad can be used to select a desred memory channel, ID lst number (dPMR), TX status (BIIS, dPMR) or Short Data Message (dPMR), or enter a desred TX code (5-tone) or ID (dPMR). OPT 1 OUT, OPT 2 OUT, OPT 3 OUT Push to output the control sgnal to the opton connector. OPT 1 MOMENTARY, OPT 2 MOMENTARY, OPT 3 MOMENTARY Outputs the control sgnal to the opton connector whle holdng down ths key. 7 BASIC OPERATION Turning the power ON q Hold down [ ] for 1 second to turn the power ON. w If the transcever s programmed for a start up password, nput the dgt codes as drected by your dealer. · The keys as below can be used for password nput: The transcever detects numbers n the same block as dentcal. Therefore "01234" and "56789" are the same. 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Channel selection Several types of channel selecton are avalable. However, dependng on the preprogrammed settngs, you can transmt when a call s receved that ncludes an unmatchng (or matchng) CTCSS (DTCS), colour code, or Indvdual or Talkgroup ID. - The selected channel s a `receve only' channel. · Time-out timer If contnuous transmsson exceeds the pre-programmed tme-out tmer lmt, the transmsson s cut off. · Penalty timer After the transmsson s cut off by the tme-out tmer, transmsson s further nhbted for the pre-programmed penalty tmer perod. If the transcever has a key assgned to TX Code CH Select, the ndcaton can be toggled between the operatng channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) s dsplayed, [CH Up] or [CH Down] selects the TX code channel. USING [TX CODE CH SELECT]: q Push [TX Code CH Select]-- a TX code channel number (or name) appears. w Push [CH Up] or [CH Down] to select the desred TX code channel. e After selectng, push [TX Code CH Select] to set. · Return to the stand-by mode. r Push [Call] to transmt the selected TX code. USING [TX CODE CH UP]/[TX CODE CH DOWN]: If the transcever has a key assgned to TX Code CH Up or TX Code CH Down, the programmed TX code channel can be drectly selected when pushed. 10 2 BASIC OPERATION USING [TX CODE ENTER]: q Push [TX Code Enter] to enter the TX code edt mode. · The dgt to be edted blnks. D TX code edit (5-tone operaton only) If the transcever has a key assgned to TX Code CH Select or TX Code Enter, TX code contents can be edted wthn the allowable dgts. USING [TX CODE CH SELECT]: q Push [TX Code CH Select] to enter the TX code channel selecton mode. · Select the desred channel before enterng the TX code channel selecton mode, f necessary. w Push [TX Code Enter] to select the desred dgt to be edted. e Push [CH Up] or [CH Down] to select the desred dgt. [. . . ] Pay crophone hanger to ground attention to polarities. for the ON/OFF Hook funcMake sure the ground tions. (See page 1) terminal of the DC power supply is grounded. t EXTERNAL SPEAKER JACK Connect a 4­8 ø external speaker. 17 CONNECTION AND MAINTENANCE 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Supplied accessories Microphone Microphone hanger and screw set Microphone hanger cable Mounting the transceiver The unversal mountng bracket suppled wth your transcever allows overhead or dashboard mountng. · Mount the transcever securely wth the 4 suppled screws to a thck surface whch can support more than 1. 5 kg. DC power cable Function name stickers*1 Sponges*2 Flat washer Felt* Spring washer Mounting bracket Flat washers Spring washers Nuts Self-tapping screws (5×16) * Used for labelling the programmable 1 Bracket bolts Mounting screws (5×12) Felt* When using self-tapping screws *Felt reduces the effects of vibration. function keys according to their assinged functions. [. . . ]