User manual ICOM BP-70

[. . . ] If an incorrect connection is made after cutting, the receiver may be damaged. · R EVER expose the receiver to rain, snow or any liquids. · R EVER touch the receiver with wet hands. [. . . ] This may reN sult in an electric shock or damage the receiver. · R EVER apply more than 25 W RF power or out of N VHF marine frequency (156. 000 to 161. 450 MHz) to the [RADIO] connector on the rear panel. · DO NOT use or place the receiver in areas with temperatures below ­20°C (­4°F) or above +60°C (+140°F) or in areas subject to direct sunlight, such as the dashboard. · DO NOT use chemical agents such as benzine or alcohol when cleaning, as they can damage the receiver's surfaces. · Place unit in a secure place to avoid inadvertent use by children. FEATURES m Dualwatch operation Two independent receivers can simultaneously receive CH87B (161. 975 MHz) and CH88B (162. 025 MHz). m Power divider bult-in A power divider is built-in the BP-70. This provides easy installation as well, since no extra antenna is necessary-- just connect the receiver between your VHF marine transceiver and an antenna. · The internal power divider protects the receiver from a transmit signal of the VHF marine transceiver. PANEL DESCRIPTIONS q Power indicator w Antenna connectors r Multi connector PC DATA OUT DATA IN DATA OUT e DC power connector q POWER INDICATOR Lights green during power ON. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. CONNECTIONS DATA PC DATA OUT OUT Bolting torque 0. 22­0. 25 N·m Wire information AWG28 to AWG16 Stripped skin length 6­8 mm DO NOT use a solid conductor cable, otherwise the connected cable may be disconnected. CAUTION: NEVER connect a 24 V DC power source directly. This will damage the receiver. Red Black Less than 2 mm Fuse replacement One fuse is installed in the supplied DC power cable. If a fuse blows or the receiver stops functioning, track down the source of the problem, if possible. Replace the damaged fuse with properly rated fuse. DATA IN to antenna AIS receiver Fuse rating: 0. 5 A PC conncetion 1 5 9 12 V battery PC DATA OUT DATA IN DATA OUT Navigation equipment PC GPS receiver 1 6 D-sub 9 Pin 13 25 Pin 2: Data Pin 5: Ground VHF Marine transceiver This connection is not necessary if you have no VHF marine transceiver. 14 D-sub 25 Pin Pin 3: Data Pin 7: Ground INSTALLATION q Attach the supplied angles to bottom side of the receiver, and tighten the two supplied screws (M3×6 mm) on each angle. w Mount the receiver securely with the four supplied screws (M5×20 mm) to a flat surface which is more than 10 mm (13/32 inch) thick and can support more than 2 kg (4. 4 lb). [. . . ] w Mount the receiver securely with the four supplied screws (M5×20 mm) to a flat surface which is more than 10 mm (13/32 inch) thick and can support more than 2 kg (4. 4 lb). Self-tapping screw Set screws Angle Spring washer Flat washer SPECIFICATIONS D General : 161. 975 MHz, 162. 025 MHz : 16K0F1D (GMSK) : 50 W nominal : ­20°C to +60°C; ­4°F to +140°F : 12 V DC nominal (10. 8 V to 15. 6 V) (negative ground) · Current drain : 0. 25 A · Dimensions (Projections not included) Without Angle : 132(W) × 34(H) × 155(D) mm 5 3/16(W) × 1 11/32(H) × 6 3/32(D) in Angle attached : 158(W) × 39(H) × 155(D) mm 6 7/32(W) × 1 17/32(H) × 6 3/32(D) in · Weight (Approx. ) Without Angle : 400 g (14. 1 oz) Angle attached : 460 g (16. 2 oz) · DATA input interface : IEC61162-1: 2000 (4, 800 bps) Sentence formatters : RMC, GGA, GNS, and GLL Input level : Less than 2 mA (When 2 V is applied) · Frequency coverage · Type of emission · Antenna impedance · Operating temp. range · Power supply requirement · DATA output interface To navigation equipment Sentence formatter Output level To PC Sentence formatter Output level : : IEC61162-2 (38, 400 bps) : VDM : 5 V, 40 mA max RS-422 ballanced type : Baud rate 38, 400 bps : VDM : ±5 V, ±35 mA typical RS-232C unballanced type D Receiver · Sensitivity : 0. 35 µV (typical) · Adjacent channel selectivity : More than 70 dB · Spurious response : More than 70 dB · Intermodulation : More than 65 dB · Hum and noise : More than 40 dB · Conducted spurious emission : Less than ­57 dBm All stated specifications are subject to change without notice or obligation. [. . . ]