User manual ICOM CS-F3G PROGRAMMING MANUAL

[. . . ] PROGRAMMING MANUAL CLONING SOFTWARE CS-F3G FOREWORD This manual explains in detail how to program each of the functions in the IC-F3GT/GS and IC-F4GT/GS VHF AND UHF TRANSCEIVERS with the CS-F3G CLONING SOFTWARE. The CS-F3G can be set up to meet any number of requirements of your customers, such as system conditions, channels, frequencies, tones, etc. IMPORTANT Before using the program, make a backup copy of the original disk. Operate the program using the backup and keep the original in a safe place. TABLE OF CONTENTS FOREWORD . i 12 PROGRAMMING for LTR® TRUNKING operation . [. . . ] The [High/Low] switch is assigned in the 3-1 KEY & DISPLAY ASSIGN (p. 7) Go to RF Power Selection Go to High/Low 29 Repeater code Station/Group code (if available) TOP 12345 Repeater code (if available) Time 12345 ID code 12345 Station/Group code 5 SCREEN MENU OPERATION-- PMR · Lock out Selects transmission lock out (temporary transmission inhibit) capability from OFF, Busy, Rpt 1 and Rpt 2. OFF : No restriction for receiving a signal. Busy : [PTT] switch cannot be activated while the operating channel/repeater is in use. Rpt1 : [PTT] switch can be activated while receiving a signal with matched CTCSS (or DTCS) tone or no signals. Rpt2 : [PTT] switch can be activated while receiving a signal with matched CTCSS (or DTCS) tone or no signals while 5-tone mute is released, or receiving an unmatched CTCSS (or DTCS) tone while 5-tone mute is activated. In addition, [PTT] switch is not activated for an extra time period in the case of when the lockout penalty timer, programmed in the Lockout Penalty Timer in 33 COMMON 2 (p. 15), is activated even if the transceiver in a transmittable condition. Go to Lockout Penalty Timer · Log IN/OFF Selects automatic ID transmission condition in relation to [PTT] switch from OFF, L-IN, L-INA, L-INI, L-OFF, LOFFA, Both, BothA1 and BothA2. L-IN : ID is transmitted when [PTT] is pushed. L-INA : ID is transmitted when [PTT] is pushed while 5-tone mute is released. 30 : ID is transmitted when [PTT] is pushed while 5-tone mute is activated. Voice transmission is impossible while 5-tone mute is activated and `SGL' is selected in CH Mute (p. L-OFF : ID is transmitted when [PTT] is released. L-OFFA : ID is transmitted when [PTT] is released while 5-tone mute is released. Both : ID is transmitted when both [PTT] is pushed and released. BothA1 : ID is transmitted when both [PTT] is pushed and released while 5-tone mute is released. BothA2 : ID is transmitted when both [PTT] is pushed and released while 5-tone mute is released. ID is transmitted when [PTT] is pushed while 5-tone mute is activated. Voice transmission is impossible while 5-tone mute is activated and when `SGL' is selected in CH Mute (p. When SmarTrunk ON/OFF is selected for the editing bank in CH Atr (p. The ID code is assigned in the 5Tone signaling-- ID column in this screen (p. 29), and the 5-tone code is programmed in TX Code in 10-2 TX CODE CH (p. [. . . ] w Log IN/OFF, Auto Reset, CH Mute Log IN/OFF: Select "L-IN" Auto Reset : Select the timer to around 1. 0 sec. which is programmed in Auto Reset Timer A or B in COMMON 1 sheet (p. CH Mute : Select "SGL" Go to Auto Reset Timer A, Auto Reset Timer B e RX C-No Click to check the channel to the desired code which is programmed in the RX CODE CHANNEL (p. Go to RX CODE CHANNEL r r 5Tone Signaling-- From, RPT, STN, ID, Pos Form : Select "DTMF" RPT : Select "OFF" STN : Select "OFF" ID : Select the channel to the desired code which is programmed in the TX CODE CHANNEL (p. [. . . ]