User manual ICOM FP-100

[. . . ] Connecting the PD-200, a DGPS beacon receiver, to this system will permit the GPS to pinpoint the ship location more accurately. Please read this instruction manual carefully to ensure correct and efficient use of the product. Cartgraphy supplied by NAVIONICS Seamless chart start from $99 and span the globe with high detail and 16 zoom levels. Ask your nearest NAVIONICS dealer for more details. SUPPLIED ACCESSORIES Qty. q Self-tapping screws (M 6 × 30)········································4 w Spring washers (M 6) ······················································4 e Flat washers (M 6)···························································4 r Connector covers·····························································2 t Horse band (HAS-40) ······················································2 y Extention pipe (2273 PIPE) ·············································1 u GPS antenna ···································································1 i Power cable (OPC-786)···················································1 q Instruction manual q y w e u r t i Versions of the FP-100 which display "CE" on the serial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility. i TABLE OF CONTENTS INTRODUCTION . [. . . ] r Select "BLUE" or "BLK" (Black) using the [UP] or [DOWN] key and press the [SET] key. t When you finish setting the color of sea, press the [MENU] key. You will return to the previous screen. CLR SEL CANC SET SET 80. 0FT 31 r PLOTTER MODE q DATA COLOR SETTING 8 Ç Specifying the color of placenames 5 SCREEN SETTING DISP MODE BKG COLOR LAND SEA NAME D CON 5m D CON 10m D CON 20m LIGHT GRID DISP MAPS 1 BLUE YELL BLUE WHIT LBLU LBLU LBLU RED BLUE WHIT 2 CSLN OFF OFF OFF OFF OFF OFF OFF CLR ADJ CANC SET SEL SET 80. 0FT The color of place-names can be selected from among seven available colors. w Select "Screen Setting" using the [UP] or [DOWN] key and press the [SET] key. e Select "NAME" using the [UP] or [DOWN] key and press the [SET] key. r Move to the color field using the [LEFT] or [RIGHT] key. The color field will be highlighted in yellow. t Select the desired color from among available colors (White (WHIT), Yellow (YELL), Light blue (LBLU), Purple (PURP), Red, Green (GREE), Blue) using the [UP] or [DOWN] key and press the [SET] key. Place-names will be displayed in the selected color. * When you select "OFF" and press the [SET] key, place-names are not displayed. y When you finish setting the color of place-names, press the [MENU] key. r Move to the color field using the [LEFT] or [RIGHT] key. The color field will be highlighted in yellow. t Select the desired color from among available colors (White (WHIT), Yellow (YELL), Light blue (LBLU), Purple (PURP), Red, Green (GREE), Blue) using the [UP] or [DOWN] key and press the [SET] key. Map border will be displayed in the selected color. * When you select "OFF" and press the [SET] key, map border are not displayed. y When you finish setting the color of map border, press the [MENU] key. You will return to the previous screen. Specifying the display mode 5 SCREEN SETTING DISP MODE BKG COLOR LAND SEA NAME D CON 5m D CON 10m D CON 20m LIGHT GRID DISP MAPS 1 BLUE YELL BLUE WHIT LBLU LBLU LBLU RED BLUE WHIT 2 CSLN OFF OFF OFF OFF OFF OFF OFF These color settings can be memorized and selected from two display modes. w Select "Plotter Menu" using the [UP] or [DOWN] key and press the [SET] key. e Select "DISP MODE" (display mode) using the [LEFT] or [RIGHT] key and press the [SET] key. Color settings will be displayed in the memorized colors. r When you finish selection, press the [MENU] key. [. . . ] Doing so may cause damage to the ship speed sensor. ¡ A transducer must be installed by a shipbuilder or an expert installer. 72 6 INSTALLATION PROCEDURE 6-6 Connecting an external navigator An external navigation equipments can be connected to the NMEA connector on the rear panel of the system. Connect a 4-pin microphone connector to the NMEA connector and plug the data line in the 1-pin connector and the data return line in the 2-pin connector. When using an external navigator, set "Positioning Equipment" to "NMEA" on the Positioning Menu screen ( P. [. . . ]