User manual ICOM HM-162B-SW

[. . . ] INSTRUCTIONS REMOTE-CONTROL MICROPHONE Thank you for purchasing the HM-162B/SW REMOTETM CONTROL MICROPHONE. The COMMANDMIC III is a remote control microphone for use with the IC-M604 or else. Please read the connected transceiver's instruction manual carefully before installation and operation. These instructions are just described the remotecontrol operations only. HM-162B/SW These instructions are described when the HM-162 is connected to the IC-M604. [. . . ] according to the Set mode setting (Channel 16 is still monitored during Priority scan). · Rotate [SELECTOR CH] to check the scanning TAG channels, to change the scanning direction or resume the scan manually. 1 · "16" blinks at the channel comment indicator and a beep tone sounds when a signal is received on Channel 16 during Priority scan. BUSY-25W---INT---CALL 25W---INT---CALL LOCAL--DUP LOCAL--DUP SCRAM--TAG SCRAM--TAG NORMAL-SCAN [CH-] -34"34. 206N 34"34. 206N 123"23. 236W --UTC 10:10--UTC-10:10- INTL Appears D Activating the All Key Lock function While pushing [H/L], turn the power ON by pushing [PWR] to turn the All Key Lock function ON or OFF. ·" " blinks. · Only [PWR] ([CLR]/[MENU]), [DISTRESS] and [PTT] are functional. é BUSY-25W---INT---CALL 25W---INT---CALL LOCAL--DUP LOCAL--DUP SCRAM--TAG SCRAM--TAG NORMAL-SCAN [CH-] -34"34. 206N 34"34. 206N 123"23. 236W --UTC 10:10--UTC-10:10- INTL Blinks t To stop the scan, repeat step r. 4 /3 Display backlight The function display and keys can be backlit for better visibility under low light conditions. The backlighting condition can also be adjusted independently from the transceiver. While pushing [H/L], rotate [SELECTOR] to adjust the backlight level. B · "BACKLIGHT " with the backlight level appears. · The backlight is adjustable in 7 levels and OFF. BUSY-25W---INT---CALL 25W---INT---CALL LOCAL--DUP SCRAM--TAG SCRAM--TAG NORMAL-SCAN BACKLIGHT -7 -<ENT OK> <ENTOK> COMMERCIAL /6 Hailer function q Push [HAIL· RX ] to enter the hailer mode. w Push and hold [PTT] and speak at a normal voice level. BUSY-25W---INT---CALL LOCAL--DUP SCRAM--TAG NORMAL-SCAN HAILER LISTEN 15. 236W 15. 236W ____al--1:10--CALLING ___ l--1:10--CALLING T · "TALK" appears. W · "WAIT" appears while the transceiver side is in use. · To adjust the hailer level, rotate [SELECTOR]. Appears e After speaking, release [PTT]. r To cancel the hailer mode, repeat step q. · Pushing [16·9] also cancels the hailer function. /4 RX Speaker function q Push [HAIL· RX ] for 1 sec. to enter the RX Speaker mode. BUSY-25W---INT---CALL BUSY 25W---INT---CALL LOCARX UP LOCARX--UP SCRAM--TAG SCRAM--TAG NORMAL-SCAN RXRX [CH-] [CH 154"34. 206N 154"34. 206N 123"23. 236W -<ENT OK>-- CALLING <ENTOK>-- While in the hailer mode, the transceiver functions (transmit and receive) are interrupted. If the transceiver is in transmit condition, the hailer function is not available. · " RX " indicator appears. · The audio output level for the RX speaker can be adjusted when entering this mode. Or while pushing [HAIL· RX ], rotate [SELECTOR] before tuning OFF this function (within for 1 sec. ). /7 Automatic foghorn The automatic foghorn function sounds a horn repeatedly until the function is turned OFF. Four patterns are available for varying conditions. The foghorn outputs from the hailer speaker. To use this function, the hailer speaker must be connected to the transceiver. See the transceiver's instruction manual for connection details. The audio frequency of the foghorn is selectable in Set mode. q While pushing and holding [H/L], push [HAIL· RX ] to enter auto foghorn mode. w Rotate [SELECTOR] to select the desired foghorn pattern, push [ENT]. BUSY-25W---INT---CALL BUSY-25W---INT---CALL LOCARX UP LOCARX--UP SCRAM--TAG SCRAM--TAG NORMAL-SCAN UNDERWAY UNDERWAY [VOL] -STOP4"34. 206N STOP4"34. 206N 123"23. 236W -<ENT OK>-- CALLING <ENTOK>-- w To cancel the RX Speaker mode, repeat step q. · " RX " indicator disappears. /5 Intercom operation q Push [LO/DX·IC SCR ] for 1 sec. [. . . ] The messages can be used as an assistance to the logbook. R q Select and enter "Received Calls" in the DSC menu. D O w Select and enter "Distress" or "Other. " e Select and enter the desired message. · Messages which are blinking have not been read. D MMSI code check The 9-digit MMSI (DSC self ID) code can be checked. M q Select and enter "MMSI Check" in the set up menu. [. . . ]