User manual ICOM IC-02N

[. . . ] WORD RWARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. It's fast and easy to select any of memory channels in the IC-02N. The "flip-flop" arrow button switches between active and standby channels. The dualwatch function allows you to monitor two channels simultaneously. [. . . ] q Set a "126. 000 MHz" in the standby indicator. RX 134. 80 126. 005 RX MEMORY "126. 00" appears in the standby indicator. 03 w Push [RCL], then rotate [ODIAL] to select "MEMORY". 134. 80 CH01 RX MEMORY "MEMORY" and regular channel number appear. memory e Select regular memory channel 4 with [DIAL]. r Push [MEM], then rotate [ODIAL] to select "REPLACE. " 134. 80 CH04 RX MEMORY " " appears when no frequency has been programmed into regular memory channel 4. 126. 000 134. 80 RX REPLACE CH04 Ç ---. --- Regular memory channel number blinks. "WRITE COMPLETED" is displayed when the selected frequency is stored. t Push [MEM] to store the desired frequency into the selected regular memory channel. MEMORY 134. 80 126. 005 CH04 TIP: Push and hold [MEM] for 2 sec. to program a displayed frequency to any blanket memory channel automatically, after step q. NOTE: The programming is cancelled while all regular memory channels have already programmed. 11 3 MEMORY OPERATION I Transferring memory contents This function transfers a memory channel's contents into the active frequency indicator. q Push [RCL] to enter the memory mode. · The channel number appears. · The memory channel name also appears if it has been entered. I Memory mode menu (Regular and group memory channels only) ï REPLACE Replacing the selected memory channel to the standby frequency. w Rotate [O-DIAL] to select the desired memory channel type. · Select regular, group history or GPS memory channel. ï DELETE Deleting the selected memory channel. e Rotate [DIAL] to select a memory channel to be transferred. r Push [], then the selected memory channel is transferred into the active frequency indicator. · The memory mode is cancelled automatically. ï REVIVE Returning the selected memory channel to its previous state. ï CH NAME (Regular memory channel only) Setting the channel name to the selected regular memory channel. RX MEMORY 122. 00 127. 005 CH01 ï GRP NAME (Group memory channel only) Setting the group name to the selected memory group. Push []. RX MEMORY ï CH TAG (Group memory channel only) Setting the channel tag to the selected memory channel (Selecting the group memory channel is the only option). 127. 00 122. 005 12 ï DONE Return to the memory mode. MEMORY OPERATION 3 I Regular memory channel The transceiver has 10 regular memory channels. q Push [RCL] to enter the memory mode. · The channel number appears. · The memory channel name also appears if it has been entered. I Group memory channel The transceiver has 200 memory channels 200 group channels (10 channels × 20 groups). q Push [RCL] to enter the memory mode. · The channel number appears. · The memory channel name also appears if it has been entered. 03 w Rotate [O-DIAL] to select the regular memory channel. · "MEMORY" appears. RX MEMORY w Rotate [O-DIAL] to select the group memory channel. · "GRP01­GRP20" appears. RX GRP01 122. 00 127. 005 CH01 122. 00 127. 005 CH01 e Rotate [DIAL] to select the desired channel. r Push [MEM], then group name's 1st digit blinks. t Rotate [DIAL] to select the desired character. · The character type as shown left "Selectable characters" is selectable. · Push [DIAL] to switch capital (A, B, C, ···) lower case (A, B, C, ···) number (0, 1, 2, ···) capital (A, B, C, ···) in order. y Rotate [O-DIAL] to select the next input digit. u Repeat t­y to input the memory channel name. i Push [MEM] to decide the memory channel name. · Selectable characters 0123456789:;<=>?@ ABCDEFGHIJKLMNOPQRSTUVWXYZ[\] ^_` abcdefghijklmnopqrstuvwxyz{|}~I!"#$ %&'()+, ­. / y Rotate [O-DIAL] to select the next input digit. u Repeat t­y to input the group name. i Push [MEM] to decide the group name. 15 3 MEMORY OPERATION I Programming channel tag (Group memory channel only) The tag name can be set a 3-character name in addition to the group number. It is convenient for separating memory type. q Push [RCL], then rotate [O-DIAL] to select the desired group memory channel in the memory mode. · Rotate [O-DIAL] to select the memory channel type if necessary. I Channel tag list DISPLAY TAG NAME Group*1 GPS*2 ___ TWR GND ATS ATF APP ARR AWS CLR CTF DEP FSS RFS UNI MF OTH U-1 U-2 YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES ­ YES YES YES YES YES YES YES YES YES YES YES YES YES ­ ­ ­ MEANS Non-tag Tower Ground ATIS Air traffic Approach Arrival Automatic Weather Station Clearance / Delivery Departure Frequency Flight Service Station Remote Flight Service Station Unicom frequency Mandatory frequency Other User1 setting (Refer to p. 24) w Push [MEM], then rotate [O-DIAL] to select "CH TAG" when selecting "LABEL" in "Group memory channel display" of the menu mode (p. [. . . ] intervals. D Beep Tone Level "BEEP" Confirmation beep tones normally sound when storing memory, operating time-out-timer function, etc. These can be set the desired beep level as you prefer. · OFF (0) : The beep tone turns OFF. · 001­100 : Setting the beep tone level from 1 to 100. 05 D Frequency Step "FREQ. STEP" Set the desired frequency step: 8. 33 kHz or 25 kHz. · 25kHz · 8. 33kHz : Setting the frequency step to 25 kHz. [. . . ]