User manual ICOM IC-1200A-E

[. . . ] This connection will ruin the transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-1200A-E VHF TRANSCEIVER and IC-F621 UHF TRANSCEIVER. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. [. . . ] Take the microphone off hook to stop scanning. Push and hold this key to indicate the scan group, then push to select the desired group. [TAG] SCAN TAG KEY Adds or deletes the selected channel to the scan group. LOCK KEY Electronically locks all programmable keys except the following: · [CALL] (incl. [CAL A] and [CAL B]), [MONI] and [EMER] keys. NOTE: The unmute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible` condition) after a specified period. [W/N] WIDE/NARROW KEY Push [W/N] to toggle bandwidth between wide or narrow. OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or permanently depending on the pre-setting. · Ask your Dealer or System Operator for the output power level for each selection. [LOCK] [H/L] 4 1 [TA] PANEL DESCRIPTION TALK AROUND KEY Turns the talk around function ON and OFF. · The talk around function equalises the transmit frequency to the receive frequency for mobileto-mobile communication. · Call transmission is necessary before you call another station depending on your signaling system. EMERGENCY KEY Push and hold the key to transmit an emergency call. Please refer `I Optional UT109/UT-110 installation'. (p. 17) · Please contact your Dealer for details. 6 2 OPERATION I Channel selection Several types channel selections are available, methods may differ according to your system set up. I Turning power ON q Push [POWER] to turn the power ON. · A power-up alert tone sounds for about 1 sec. and an opening message may appear. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your Dealer. · The keys in the table below can be used for password input: · The transceiver detects numbers in the same block as identical. Therefore "01234" and "56789" are the same. NON-BANK TYPE: Push [CH UP]/[CH DN] to select the desired operating channel, in sequence; or, push one of the [CH 1] to [CH 4] to select a channel directly. BANK-TYPE: Push [BANK] to select the desired bank number. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook. KEY NUMBER [P0] 0 5 [P1] 1 6 [P2] 2 7 [P3] 3 8 [P4] 4 9 e When the "PASSWORD" indication does not clear after inputting 4 digits, the input code number may be incorrect. Turn power off and start over in this case. 7 OPERATION 2 I Receiving and transmitting RECEIVING: q Push [POWER] to turn the power ON. w Push [CH UP] or [CH DN] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. [. . . ] Ask your Dealer about antennas and the best places to mount them. I Fuse replacement Two fuses are installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the problem, if possible, and replace the damaged fuse with a new rated one. Fuse rating : 20 A, I Cleaning OPTIONAL CABLE PIN ASSIGNMENT trewq q LCD backlit cont. GND If the transceiver becomes dusty or dirty, wipe it clean with a dry, soft cloth. AVOID the use of solvents such as benzene or alcohol, as they may damage transceiver surfaces. oiuy 18 5 OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install. [. . . ]